Avaya Configuring WAN Lines Services Manual do Utilizador Página 235
- Página / 462
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuring FT1 Services
308648-14.00 Rev 00
8-33
Valid options are:
• Mark -- This format uses a 0-bit to indicate a state change and a 1-bit to
indicate no state change.
• Space -- This format uses a 1-bit to indicate a state change and a 0-bit to
indicate no state change.
See the NRZI Type parameter on page A-55 for information.
Assigning Timeslots
After configuring logical lines, you configure channels (DS0s) of bandwidth by
grouping 1 to 24 contiguous or noncontiguous DS0 timeslots per DS1 frame.
Allocating DS0s
If you have an FT1/T1 DSU/CSU or E1 module and an ISDN S/T or U module
installed on the same ARN router, you can alternate assigned DS0 channels with
unassigned channels, up to a maximum rate of 512 Kb/s (8 channels).
If you have rates above 512 Kb/s, Nortel Networks recommends that you
configure the DS0 contiguously, even though some noncontiguous channel
configurations may work. If you have an unsupported channel configuration, the
following message appears in the event log:
Connector COM <COM#>, Current timeslot assignment is not supported.
This message indicates an invalid assignment of DS0s for the specified connector;
you should have your service provider change the T1 channel assignments. Using
contiguous channel assignments addresses this problem.
Selecting 56K Rate Adaption on FT1/T1 DSU/CSU Lines
Rate adaption determines the number of bits and their bit positions within a time
slot. The FT1/T1 logical line rate adaption is 64 Kb/s per DS0. You cannot change
this rate.
Caution:
You cannot alternate assigned and unassigned channels across the 24
channels in a T1 line (768 Kb/s).
- Configuring WAN Line 1
- Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308648-14.00 Rev 00 10
- Before You Begin 33
- Text Conventions 34
- Acronyms 35
- Hard-Copy Technical Manuals 38
- How to Get Help 39
- Chapter 1 41
- Getting Started 41
- Accessing Line Parameters 44
- shows where to 46
- Table 1-2. WAN Line Types 47
- Chapter 2 49
- Setting the BofL Timeout 54
- Setting Minimum Frame Spacing 62
- Setting the Signaling Method 67
- Setting the Line Coding 69
- Configuring KG84A Security 69
- LS0017A 70
- Setting the Retry Count 73
- Setting the Link Idle Timer 73
- Setting the Cable Type 74
- Setting the Retry Timer 75
- Setting a Priority 76
- Setting the Hold Down Time 77
- Setting the IFTF Pattern 78
- Resetting EIA Signal Status 91
- Chapter 3 93
- Asynchronous Services 93
- Setting the Baud Rate 96
- Setting the Idle Timer 97
- Chapter 4 99
- Configuring DSU/CSU Services 100
- Site Manager 101
- Setting the Option Mode 102
- Resetting the Router 103
- Configuring Line Availability 104
- Resetting the CQMS Counters 105
- Setting the Poll Rate 105
- Caution: 106
- Using the BCC 107
- Using Site Manager 107
- AN/ANH/ARN 109
- Local Analog Loopback (AL) 110
- Chapter 5 113
- Configuring HSSI Services 113
- Enabling or Disabling BofL 115
- Setting the BofL Interval 116
- Setting the MTU 117
- Setting the CRC Size 119
- Configuring WAN Line Services 122
- Chapter 6 123
- Editing T1 Services 124
- (Figure 6-1) 125
- Setting the T1 Frame Type 126
- Figure 6-2. Bipolar Format 127
- Specifying Line Buildout 128
- Assigning Channel Functions 129
- Editing E1 Services 130
- Enabling or Disabling CRC 132
- Setting the Clock Source 132
- Chapter 7 135
- Setting the Clock Parameters 139
- (continued) 141
- (continued) 142
- Setting the MCE1 Line Type 143
- Setting the MCE1 Line Coding 143
- Setting the Loop Clock 146
- Setting the External Clock 146
- Setting the MCT1 Line Type 152
- Carrier-to-Customer 156
- Setting Relay Control 159
- Configuring a DS0A Connection 164
- Setting Parameters 165
- Defining Logical Lines 169
- Circuit name: MCE1_31_1 171
- E1 CRC MF 187
- Testing MCE1 and MCT1 Lines 190
- Setting Port Test Parameters 191
- Table 7-19. ESF Line Types 194
- Running Port Tests 195
- Running Logical Line Tests 200
- Chapter 8 203
- Configuring FT1 Services 203
- Setting the FT1 Line Type 209
- Setting the FT1 Line Coding 210
- Setting the Signal Level 211
- Type of circuit 225
- Slot where connector 225
- Logical line 225
- Assigning Timeslots 235
- Chapter 9 245
- Configuring FE1 Services 245
- Setting the FE1 Line Type 250
- Setting the FE1 Line Coding 251
- Circuit name: 257
- Testing FE1 Lines 269
- About the Tests 270
- Chapter 10 277
- Types of Multiline Circuits 278
- Multiline Example 279
- Software Considerations 280
- (MCE1 Example) 289
- Logical Lines (MCE1 Example) 291
- Appendix A 295
- Site Manager Parameters 295
- Asynchronous Line Parameters 296
- DSU/CSU Parameters 302
- E1 Line Parameters 304
- HSSI Line Parameters 307
- LAPB Parameters 312
- MCE1 Port Parameters 319
- MCT1 Port Parameters 323
- FT1 Port Parameters 338
- FT1 Logical Line Parameters 344
- FE1 Line Parameters 350
- FE1 Clock Parameters 351
- FE1 Port Parameters 352
- FE1 Logical Line Parameters 357
- Synchronous Line Parameters 363
- T1 Line Parameters 382
- Appendix B 387
- BCC show Commands 387
- <circuit_name> 389
- <slot> 389
- Receive Errors 391
- Transmit Errors 391
- System Errors 393
- <number_of_seconds> 394
- Commands for HSSI Services 411
- E1 framers 431
- Commands for Serial Services 439
- Appendix C 451
- <slot_no.> 452
- Glossary 453
Manuais e produtos relacionados com Redes Avaya Configuring WAN Lines Services
Redes Avaya 1220 Manual do Utilizador
(180 páginas)
(180 páginas)
Redes Avaya BCM Imaging Tool Guia do Utilizador
(42 páginas)
(42 páginas)
Redes Avaya BCM50 Guia do Utilizador
(40 páginas)
(40 páginas)
Redes Avaya R6.0 Nota de Aplicação
(30 páginas)
(30 páginas)
Redes Avaya AP-8 Nota de Aplicação
(22 páginas)
(22 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais