Avaya Configuring Line Services Manual do Utilizador Página 128
- Página / 268
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuring Line Services
4-28
Parameter: Enable Rx/Tx of XID Frames
Default: Enable
Options: Enable
| Disable
Function: Enables or disables the transmission and reception of test exchange
identification (XID) frames by the router.
Instructions: Select Enable to allow the router to send XID frames. Select Disable to
prevent the router from sending XID frames.
MIB Object ID: 1.3.6.1.4.1.18.3.5.1.8.1.17
Parameter: Idle RR Frames
Default: Off
Options: On
| Off
Function: Enables or disables the transmission and reception of Receiver Ready
(RR) frames during periods when there are no information frame
exchanges. When this parameter is set to On, an RR is transmitted when
no traffic is present on the physical media.
Instructions: Select On or Off.
MIB Object ID: 1.3.6.1.4.1.18.3.5.1.8.1.40
Parameter: Command/Response Address
Default: DTE
Options: DTE
| DCE
Function: Specifies the local command or response address, which is the DTE or
DCE value expressed as a single octet.
Instructions: Enter DTE for the DTE address, or DCE for the DCE address.
MIB Object ID: 1.3.6.1.4.1.18.3.5.1.8.1.18
- Configuring Line Services 1
- Bay Networks Software License 3
- (continued) 4
- Contents 5
- About This Guide 17
- CompuServe 19
- How to Get Help 20
- Conventions 21
- Acronyms 22
- Chapter 1 25
- Overview of Line Protocols 25
- Concentrator 26
- Data Flow 27
- Medium Access Control 27
- Carrier Sense Multiple Access 27
- Collision Detection 27
- Ethernet Frame Formats 27
- Ethernet Media 28
- Token Ring Overview 29
- FDDI Overview 30
- FDDI Ring Operation 33
- Station Timers 34
- FDDI Ring Maintenance 34
- FDDI SMT 34
- SMT Frame Services 35
- Wide Area Circuits 37
- T1 Synchronization 38
- T1 Frame Format 39
- Figure 1-10. D4 Frame 40
- E1 Services 41
- WAN Protocols 42
- Chapter 2 43
- Accessing Line Services 43
- Editing Line Details 47
- Chapter 3 49
- Customizing Line Protocols 49
- Editing E1 Line Details 50
- 51
- 52
- 52
- Editing Ethernet Line Details 54
- 57
- 57
- 60
- Editing FDDI Line Details 63
- Editing FDDI SMT Attributes 66
- Editing FDDI MAC Attributes 72
- Editing FDDI Port Attributes 76
- Editing HSSI Line Details 78
- Editing T1 Line Details 82
- 88
- 88
- Editing ATM Line Details 89
- 95
- 99
- Chapter 4 101
- Customizing Synchronous and 101
- Asynchronous Lines 101
- 103
- 105
- 106
- 107
- 108
- 1 Address of the DCE 111
- 3 Address of the DTE 111
- 113
- 113
- 114
- 114
- 116
- Point-to-Point Addresses 118
- KG84A Support 119
- 2. Click on LAPB 123
- 125
- 125
- 127
- 131
- Chapter 5 135
- Configuring MCE1 135
- Setting Clock Parameters 136
- Configuring MCE1 137
- 4. Click on OK 137
- Configuring the MCE1 Port 141
- 142
- 144
- Configuring Non-PRI Circuits 144
- Click on Add 145
- 2. Click on Circuit 150
- 10. Select File➔Exit 153
- Configuring the Logical Line 154
- 156
- 158
- 159
- Assigning Timeslots 160
- Saving Your Changes 162
- • Assign timeslots 163
- • Save your changes 163
- Testing MCE1 Lines 165
- Setting the Test Parameters 166
- 168
- Running the Tests 170
- Chapter 6 171
- Configuring MCT1 171
- Adding MCT1 Circuits 172
- 2. Click on OK 176
- 177
- Setting MCT1 Port Parameters 178
- To edit MCT1 port parameters: 179
- Click on OK 179
- 180
- Configuring MCT1 181
- 182
- 184
- Select File➔Exit 193
- MCT1-31-1 193
- Click on a timeslot 201
- Testing MCT1 Lines 206
- Click on Line Tests 207
- 210
- 5. Click on Done 212
- Setting Test Parameters 214
- Chapter 7 219
- Configuring Multiline Services 219
- Types of Multiline Circuits 220
- Grouping Data Paths 221
- Multiline Traffic Distribution 222
- Frame Relay Considerations 223
- PPP Multilink 223
- Configuring Multiline 224
- 229
- Chapter 8 231
- Managing Line Resources 231
- Line Resource Manager (LRM) 232
- Supported Media 233
- How LRM Works with ST2 233
- 237
- 238
- 240
- Accessing LRM on an MCT1 Line 242
- Deleting LRM Services 244
- Appendix A 247
- FDDI Line Parameters 248
- HSSI Line Parameters 249
- T1 Line Parameters 250
- Token Ring Line Parameters 250
- ATM FRE2 Line Parameters 250
- ATM ARE Line Parameters 251
- Synchronous Line Parameters 252
- LAPB Parameters 253
- Asynchronous Line Parameters 254
- MCE1 Line Parameters 255
- MCT1 Line Parameters 256
- Multiline Parameters 259
- Line Resource Parameters 259
Manuais e produtos relacionados com Redes Avaya Configuring Line Services
Redes Avaya E1 Manual do Utilizador
(52 páginas)
(52 páginas)
Redes Avaya BCM Imaging Tool Guia do Utilizador
(40 páginas)
(40 páginas)
Redes Avaya an Expansion Module in a BayStack ARN Router (114202 Rev. A) Manual do Utilizador
(40 páginas)
(40 páginas)
Redes Avaya BayRS Version 15.7.0.0 Aviso
(80 páginas)
(80 páginas)
Redes Avaya SIP DECT Fundamentals Manual do Utilizador
(292 páginas)
(292 páginas)
Redes Avaya BCM450 Manual do Utilizador
(92 páginas)
(92 páginas)
Redes Avaya Nortel Business Communications Manager 450 1.0 Guia de Resolução de Problemas
(102 páginas)
(102 páginas)
Redes Avaya BCM 3.6 Manual do Utilizador
(12 páginas)
(12 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.168 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais