Avaya Configuring IP Services Manual do Utilizador Página 36
- Página / 466
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuring IP Services
2-8
Configuring a MAC Address for an Adjacent Host
An adjacent host is a device on a locally attached network. This device may or
may not be a router. You must configure a media access control (MAC) address for
each adjacent host that does not implement the Address Resolution Protocol
(ARP).
Also, if a local network does implement ARP, you may want to configure a MAC
address for an adjacent host to pre-empt the ARP process.
Selecting an Address Resolution Protocol
The IP router needs both a physical address and an IP address to transmit a
datagram. In situations where the router knows only the network host’s IP address,
the Address Resolution Protocol (ARP) enables the router to determine a network
host’s physical address by binding a 32-bit IP address to a 48-bit MAC address. A
router can use ARP across a single network only, and the network hardware must
support physical broadcasts.
Figure 2-3. ARP Example
For instructions on using Site Manager to configure a connection to an adjacent host, see
“Configuring a Path to an Adjacent Host” on page 2-68.
Host
B
Host
C
Host
A
Router
140.250.200.0
140.250.200.1
00 00 A2 00 00 01
140.250.200.2
00 00 A2 00 10 20
140.250.200.3
00 00 A2 00 10 30
140.250.200.4
00 00 A2 00 10 40
- Configuring IP Services 1
- Bay Networks Software License 3
- About This Guide 5
- Software Suites 6
- Audience 7
- CompuServe 8
- InfoFACTS 8
- How to Get Help 9
- Conventions 10
- Acronyms 11
- Chapter 1 13
- IP Datagrams 14
- IP Addresses 15
- Subnet Addressing 16
- (continued) 19
- Border Gateway Protocol (BGP) 22
- Route Preferences 23
- Route Weights 24
- IP Traffic Filters 27
- RFC Compliance 27
- Chapter 2 29
- Configuring IP Interfaces 30
- Multinet Interfaces 31
- Next-hop address 0 33
- Next-hop mask equals 0 33
- Subnet Broadcast Addresses 35
- Proxy ARP 38
- Inverse ARP 39
- HP Probe 39
- Security Label Format 45
- How RIPSO Works on the Router 46
- Inbound IP Datagrams 47
- Forwarded IP Datagrams 48
- Originated IP Datagrams 48
- Unlabeled IP Datagrams 48
- RIPSO Example 49
- Defining a Static Route 50
- BFE Addressing 53
- IP over ATM 57
- Configuring Host-Only Mode 58
- Editing IP Parameters 59
- Editing IP Global Parameters 80
- finished 81
- Deleting IP from an Interface 89
- Configuring Static Routes 91
- Editing a Static Route 92
- Deleting a Static Route 96
- Adding an Adjacent Host 97
- Configuring IP Services 100
- Editing TFTP Parameters 101
- Configuring RIPSO Support 104
- Configuring Router Discovery 114
- (continued) 119
- Settings 121
- Chapter 3 123
- Configuring RIP Services 123
- Sending RIP Updates 124
- Sending Triggered Updates 125
- Receiving RIP Updates 126
- Configuring RIP Services 127
- Setting RIP Timers 128
- Enabling RIP2 Authentication 128
- Specifying the RIP Diameter 129
- Editing RIP Parameters 129
- Configuring RIP on the Router 130
- RIP Parameter Descriptions 131
- Chapter 4 139
- Configuring OSPF Services 139
- Specifying Network Types 141
- Configuring OSPF Services 143
- Establishing Adjacencies 144
- Dividing an AS into Areas 145
- Configuring a Border Router 148
- Configuring a Boundary Router 152
- Figure 4-6. OSPF ASE Routes 154
- Configuring Cost Metrics 156
- Table 4-1. OSPF Area Routers 159
- OSPF Implementation Notes 160
- Editing OSPF Parameters 161
- Configuring OSPF on the Router 162
- Editing an OSPF Interface 165
- Example: 178
- Editing OSPF Area Parameters 182
- Adding an Area 183
- Editing an Area 184
- Deleting an Area 186
- Adding a Range to an Area 187
- Editing an Area’s Range 190
- Deleting a Range from an Area 192
- Editing a Neighbor 195
- Deleting a Neighbor 196
- Adding a Virtual Interface 198
- Editing a Virtual Interface 199
- Deleting a Virtual Interface 203
- Chapter 5 205
- Configuring BGP Services 205
- BGP Features 206
- Configuring BGP Services 207
- Configuring BGP on the Router 208
- Selecting the BGP Version 208
- Initiating a Connection 210
- Negotiating a Connection 211
- Keeping the Connection Alive 212
- Terminating a Connection 212
- BGP Messages 213
- Keepalive Message 214
- Update Message 214
- BGP-3 Update Message Format 215
- BGP-4 Update Message Format 216
- . (dot or period) 218
- Notification Message 219
- How BGP Selects the Best Path 221
- Routing Policies 222
- OSPF/BGP Interaction 224
- Using IBGP in a Transit AS 225
- BGP Implementation Notes 227
- Editing BGP Parameters 228
- Editing BGP Global Parameters 232
- Adding a BGP Peer 242
- Deleting a BGP Peer 251
- Generating BGP Event Messages 256
- Click on Add 257
- Deleting BGP from the Router 259
- 2. Click on OK 260
- Chapter 6 261
- Configuring EGP Services 261
- Running RIP 262
- Neighbor Acquisition Phase 263
- Configuring EGP Services 265
- Neighbor Reachability Phase 266
- Router A 268
- Router B 268
- Network Reachability Phase 269
- EGP Implementation Notes 271
- Editing EGP Parameters 272
- Configuring EGP on the Router 273
- Configuring EGP Neighbors 275
- 3. Click on EGP Neighbor 276
- Adding an EGP Neighbor 277
- Editing an EGP Neighbor 279
- Deleting an EGP Neighbor 281
- Deleting EGP from the Router 282
- Chapter 7 283
- Configuring IP Multicasting 283
- Host Groups 284
- How IGMP Works 285
- Configuring IP Multicasting 287
- Figure 7-1. Multicast Routers 287
- Advertising a Route 289
- Creating a Shortest-Path Tree 289
- Identifying a Leaf Network 290
- Pruning a Shortest-Path Tree 290
- Aging a Route 291
- Specifying a Threshold 291
- Types of Multicast Support 293
- Adding a DVMRP Tunnel 308
- 3. Click on Save 312
- Chapter 8 317
- Configuring NetBIOS over IP 317
- Overview of NetBIOS Services 318
- Configuring NetBIOS over IP 319
- Aging a Cache Entry 323
- Customizing a Cache Search 323
- Editing NetBIOS Parameters 325
- NetBIOS Global Parameters 327
- Chapter 9 339
- Configuring IP Policies 339
- Figure 9-1. IP Routing Table 340
- Configuring IP Policies 341
- Configuring Accept Policies 343
- Configuring Announce Policies 359
- Chapter 10 385
- 2. Click on Edit 394
- OSPF Route Filters 395
- 3. Click on OK 401
- BGP-3 Route Filters 405
- EGP Route Filters 418
- Appendix A 429
- Site Manager Default Settings 429
- Table A-5. IP Static Routes 432
- Table A-6. TFTP Parameters 432
- Table A-8. RIPSO Parameters 433
- NetBIOS over IP 435
- BGP Parameters 436
- EGP Parameters 438
- OSPF Parameters 439
- Appendix B 443
- Route Weight Worksheet 443
- Appendix C 447
- IP/OSPF Configuration 447
- IP/OSPF Configuration 449
Manuais e produtos relacionados com Software Avaya Configuring IP Services
Software Avaya FireWall-1 Manual do Utilizador
(68 páginas)
(68 páginas)
Software Avaya PeriReporter Manual do Utilizador
(122 páginas)
(122 páginas)
Software Avaya PeriProducer 3.00 (Software Release 3.00) - Business Communications Manager Aviso
(48 páginas)
(48 páginas)
Software Avaya Business Communications Manager - Intelligent Contact Center Manual do Utilizador
(258 páginas)
(258 páginas)
Software Avaya BCM50 Guia de Configuração
(568 páginas)
(568 páginas)
Software Avaya 15-601067 Manual do Utilizador
(50 páginas)
(50 páginas)
Software Avaya SMON C360 Manual do Utilizador
(286 páginas)
(286 páginas)
Software Avaya 15-601063 Manual do Utilizador
(460 páginas)
(460 páginas)
Software Avaya DXX-1015-01 Manual do Utilizador
(74 páginas)
(74 páginas)
Software Avaya NN44400-114 Manual do Utilizador
(130 páginas)
(130 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais