Avaya Configuring WAN Line Services Manual do Utilizador Página 277
- Página / 294
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Site Manager WAN Line Services Parameters
117345-B Rev. 00
A-69
Parameter: Hold Down Time
Path: COM Connector > Edit Line > Edit SYNC Parameters
Default: 0 seconds
Options: 0 to 9999 seconds
Function: Specifies the time that the router waits before bringing up this line when using
dial services. This delay allows time for the primary line to recover before
deactivating a backup line.
Instructions: Specify the number of seconds to wait before bringing up this line.
MIB Object ID: 1.3.6.1.4.1.18.3.4.5.1.80
Parameter: Network Link Level
Path: COM Connector > Edit Line > Edit SYNC Parameters
Default: NET2
Options: NET2
|
GOSIP
|
SYNC_TYPE_C03
Function: Indicates the link level for this synchronous point-to-point connection.
Instructions: Accept the default, NET2, for most configurations, or do the following:
• Change to GOSIP when this synchronous point-to-point connection is part of
a GOSIP-compliant network, such as the Department of Defense (DoD).
• Change to SYNC_TYPE_C03 when you are running X.25 on the QSync,
DST, or ESAF synchronous link modules.
MIB Object ID: 1.3.6.1.4.1.18.3.4.5.1.81
Parameter: Cable Type
Path: COM Connector > Edit Line > Edit SYNC Parameters
Default: Null
Options: Null
|
RS232
|
RS422
|
V35
|
X21
Function: Specifies the cable interface to the network.
Instructions: When the interface connects to a dial-up device for switched services, set this
parameter to reflect the cable interface type that connects the dial unit. For an
SDLC interface, specify RS232.
MIB Object ID: 1.3.6.1.4.1.18.3.4.5.1.83
- Configuring 1
- WAN Line Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117345-B Rev. 00 10
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- Bay Networks Customer Service 24
- How to Get Help 24
- Chapter 1 27
- Getting Started 27
- To edit a circuit: 33
- Figure 1-4. Edit Lines Window 34
- Chapter 2 35
- Setting the BofL Timeout 41
- Setting the MTU 41
- Configuring Clocking Signals 43
- Setting the Signal Mode 45
- Setting Minimum Frame Spacing 49
- Setting the CRC Size 52
- Setting the Signaling Method 54
- Setting the Line Coding 55
- Configuring KG84A Security 55
- Setting the Retry Count 59
- Setting the Link Idle Timer 60
- Setting the Cable Type 61
- Setting the Retry Timer 61
- Setting a Priority 62
- Setting the Hold Down Time 63
- Setting the IFTF Pattern 65
- Chapter 3 77
- Asynchronous Services 77
- for information 78
- Setting the Remote IP Address 79
- Specifying the Remote Port 80
- Specifying the Local Port 80
- Setting the Idle Timer 81
- Chapter 4 83
- Setting the Option Mode 85
- Loopback Test Modes 89
- AN/ANH/ARN 90
- Chapter 5 93
- Enabling or Disabling BofL 96
- Using the BCC 100
- Using Site Manager 100
- Configuring HSSI Services 101
- Chapter 6 103
- Editing T1 Services 104
- Setting the T1 Frame Type 105
- Configuring WAN Line Services 106
- Figure 6-2. Bipolar Format 106
- Specifying Line Buildout 107
- Assigning Channel Functions 108
- Editing E1 Services 109
- Enabling or Disabling CRC 111
- Setting the Clock Source 111
- Chapter 7 113
- Setting the Clock Parameters 116
- Configuring a DS0A Connection 129
- Setting Parameters 131
- Table 7-2 132
- Defining Logical Lines 133
- (MCT1 Example) 134
- Circuit Name: MCE1_31_1 135
- Circuit name: MCE1_231_1 135
- (MCE1 Example) 136
- See the following sections: 137
- Caution: 139
- Assigning Timeslots 144
- About the Tests 149
- Setting Port Test Parameters 150
- Running Port Tests 153
- Running Logical Line Tests 158
- Send Command Function 159
- Chapter 8 161
- Configuring FT1 Services 161
- Configuring an FT1 Port 162
- Defining Logical Line 172
- Circuit name: 174
- Chapter 9 189
- Types of Multiline Circuits 190
- Multiline Example 191
- Software Considerations 192
- Logical Lines (MCE1 Example) 205
- Appendix A 209
- Asynchronous Line Parameters 210
- DSU/CSU Parameters 216
- E1 Line Parameters 218
- HSSI Line Parameters 221
- LAPB Parameters 226
- MCE1 Port Parameters 233
- MCT1 Port Parameters 237
- FT1 Port Parameters 252
- FT1 Logical Line Parameters 258
- Synchronous Line Parameters 263
- T1 Line Parameters 282
- Glossary 287
Manuais e produtos relacionados com Redes Avaya Configuring WAN Line Services
Redes Avaya X.25 Manual do Utilizador
(148 páginas)
(148 páginas)
Redes Avaya BayRS Version 13.10 Manual do Utilizador
(104 páginas)
(104 páginas)
Redes Avaya Configuring IP Services Manual do Utilizador
(585 páginas)
(585 páginas)
Redes Avaya BCM1000 Manual de Instalação
(90 páginas)
(90 páginas)
Redes Avaya BCM 4.0 Networking Guia de Configuração
(758 páginas)
(758 páginas)
Redes Avaya Configuring IP Services Manual do Utilizador
(610 páginas)
(610 páginas)
Redes Avaya BCM3.x Manual do Utilizador
(28 páginas)
(28 páginas)
Redes Avaya V.34 Manual do Utilizador
(34 páginas)
(34 páginas)
Redes Avaya 1D5 Aviso
(40 páginas)
(40 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais