Avaya Configuring Line Services Manual do Utilizador Página 48
- Página / 301
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuring Line Services
2-12 114078 Rev. A
Neighbor Information Frames identify the upstream and downstream neighbors of
each node. After the nodes learn the addresses of their upstream neighbors, you
can use the addresses to create a logical map showing the order in which nodes
appear in the token path. A Bay Networks station issues a response to the sender
of a NIF frame and generates NIF requests as part of the neighbor notification
process.
Status Information Frames exchange information about each node, including the
status of each port on the node. You can use SIFs to create a physical map
showing the position of each station in the FDDI network. There are two types of
SIFs:
• SIF configuration frames, which show the configuration information of a
node.
• SIF operation frames, which show the operational information of a node. A
Bay Networks station issues a response to the sender of a SIF request frame.
Echo Frames verify that nodes on an FDDI network can communicate with each
other. Echo frames are used to test connectivity only. A node sends an echo
request (which is a directed packet) to another FDDI node. The receiver of the
echo request copies the data that appears in the information field of the frame and
transmits an echo response frame back to the originator of the echo request. A Bay
Networks station issues a response to the sender of an echo request frame.
Request Denied Frames deny requests from the network. If the SMT agent
receives a frame with an unsupported SMT version or an unknown frame type, it
sends a Request Denied frame. A Bay Networks station issues an RDF Response
frame.
Status Report Frames allow the Status Report protocol to report node conditions
and events. A condition is when a node enters a specific state (for example,
duplicate address detected). An event is an immediate occurrence (for example,
the generation of a trace). A Bay Networks station issues an SRF announcement
frame.
Parameter Management Frames allow the Parameter Management protocol to
manage an FDDI node. A management station performs operations on the MIB
attributes of a node by exchanging frames between the management station and
the FDDI node. To obtain an attribute, the management station initiates a PMF
Get Request frame. The FDDI node to which the PMF Get Request frame was
sent responds by initiating a PMF Get Response frame. A Bay Networks station
issues a response to the sender of a PMF Get Request frame.
- Configuring Line 1
- Services 1
- Bay Networks Software License 3
- Contents 5
- 114078 Rev. A vii 7
- 114078 Rev. A ix 9
- 114078 Rev. A 10
- 114078 Rev. A xi 11
- 114078 Rev. A xiii 13
- 114078 Rev. A xv 15
- 114078 Rev. A xvii 17
- 114078 Rev. A xix 19
- About This Guide 21
- Before You Begin 22
- Conventions 22
- Acronyms 23
- 114078 Rev. A xxv 25
- Bay Networks Customer Service 26
- World Wide Web 27
- Customer Service FTP 27
- Support Source CD 28
- CompuServe 28
- InfoFACTS 29
- How to Get Help 29
- Chapter 1 31
- Getting Started 31
- 1-2 114078 Rev. A 32
- Click on Edit 33
- (Figure 1-3) 33
- Select Lines > Edit Lines 34
- The Edit Lines window appears 34
- Chapter 2 37
- About Line Protocols 37
- Ethernet Overview 38
- 2-4 114078 Rev. A 40
- ConcentratorConcentrator 41
- 2-6 114078 Rev. A 42
- 2-8 114078 Rev. A 44
- Station Timers 45
- 2-10 114078 Rev. A 46
- SMT Frame Services 47
- 2-12 114078 Rev. A 48
- Token Ring Overview 49
- 2-14 114078 Rev. A 50
- Figure 2-7. Token Ring LAN 50
- Overview of WAN Protocols 51
- HSSI Overview 52
- ISDN Overview 52
- MCE1 and MCT1 Overview 53
- Synchronous Overview 54
- T1 Overview 54
- Figure 2-8. D4 Frame 55
- 2-20 114078 Rev. A 56
- Figure 2-10. Bipolar Format 57
- Chapter 3 58
- Customizing LAN Interfaces 58
- Setting the BofL Interval 59
- 3-4 114078 Rev. A 61
- 3-6 114078 Rev. A 63
- Editing FDDI Lines 65
- 3-10 114078 Rev. A 67
- 2. Click on SMT Attributes 67
- 3-12 114078 Rev. A 69
- 3-14 114078 Rev. A 71
- Editing FDDI Path Attributes 72
- 3-16 114078 Rev. A 73
- 2. Click on Path Attributes 73
- Editing FDDI Port Attributes 74
- Editing Token Ring Lines 75
- Specifying the Ring Speed 76
- Chapter 4 78
- Customizing WAN Interfaces 78
- 4-2 114078 Rev. A 79
- Setting the Framing Mode 81
- Editing ATM FRE-2 Lines 83
- 4-8 114078 Rev. A 85
- Editing E1 Lines 87
- Assigning Channel Functions 88
- Editing HSSI Lines 89
- 4-14 114078 Rev. A 91
- Editing T1 Lines 93
- Chapter 5 96
- Customizing Synchronous and 96
- Asynchronous Interfaces 96
- Specifying the Start Protocol 97
- 114078 Rev. A 5-3 98
- Setting the Baud Rate 99
- Setting the Idle Timer 99
- 114078 Rev. A 5-5 100
- Configuring Line Services 101
- 5-6 114078 Rev. A 101
- 114078 Rev. A 5-7 102
- Setting the Station Type 103
- Setting the Control Field 103
- Setting the Window Size 104
- Setting the N2 Retry Count 104
- Setting the Link Setup Action 105
- 114078 Rev. A 5-11 106
- Editing Synchronous Lines 107
- 114078 Rev. A 5-13 108
- Setting the BofL Timeout 109
- Setting the Clock Source 110
- 5-16 114078 Rev. A 111
- Setting the Signal Mode 112
- 5-18 114078 Rev. A 113
- Setting Minimum Frame Spacing 114
- 5-20 114078 Rev. A 115
- 114078 Rev. A 5-21 116
- Setting the CRC Size 117
- Setting the Signaling Method 117
- Setting the Line Coding 118
- Setting the Retry Count 119
- Setting the Link Idle Timer 119
- Setting the Cable Type 120
- Setting the Retry Timer 120
- Setting Sync Priority 121
- Configuring KG84A Security 122
- LS0017A 123
- 114078 Rev. A 5-29 124
- 5-30 114078 Rev. A 125
- Chapter 6 126
- Setting the Clock Parameters 128
- Customizing MCE1 Port Details 129
- 114078 Rev. A 6-5 130
- 6-6 114078 Rev. A 131
- Customizing MCT1 Port Details 132
- 6-8 114078 Rev. A 133
- 114078 Rev. A 6-9 134
- 6-10 114078 Rev. A 135
- 114078 Rev. A 6-11 136
- 6-12 114078 Rev. A 137
- 114078 Rev. A 6-13 138
- Defining Logical Lines 140
- (MCE1 example) 142
- Customizing Logical Lines 143
- 114078 Rev. A 6-19 144
- 6-20 114078 Rev. A 145
- 114078 Rev. A 6-21 146
- 6-22 114078 Rev. A 147
- 114078 Rev. A 6-23 148
- 6-24 114078 Rev. A 149
- Assigning Timeslots 150
- 2. Click on B-Channels 152
- 114078 Rev. A 6-29 154
- Chapter 7 156
- Configuring Multiline Services 156
- Multiline Example 157
- Types of Multiline Circuits 158
- Grouping Data Paths 159
- Multiline Traffic Distribution 160
- Frame Relay Considerations 161
- PPP Multilink 161
- Configuring Multiline 162
- 114078 Rev. A 7-9 164
- 114078 Rev. A 7-11 166
- 114078 Rev. A 7-13 168
- 114078 Rev. A 7-15 170
- Select File > Exit 171
- (Figure 7-12) 171
- 114078 Rev. A 7-17 172
- Chapter 8 174
- Managing Line Resources 174
- Line Resource Manager (LRM) 175
- Starting the LRM 176
- Configuring the LRM 179
- 8-8 114078 Rev. A 181
- 8-10 114078 Rev. A 183
- 114078 Rev. A 8-11 184
- Deleting LRM Services 185
- 5. Click on OK 186
- Appendix A 188
- 189
- 190
- 190
- 191
- A-6 114078 Rev. A 193
- A-10 114078 Rev. A 197
- 114078 Rev. A A-11 198
- 200
- 200
- 202
- A-16 114078 Rev. A 203
- 114078 Rev. A A-17 204
- A-18 114078 Rev. A 205
- 209
- 213
- 214
- 215
- A-30 114078 Rev. A 217
- 218
- 219
- 220
- A-34 114078 Rev. A 221
- 114078 Rev. A A-35 222
- 223
- 114078 Rev. A A-37 224
- 225
- 227
- 227
- 228
- 232
- 234
- 236
- A-50 114078 Rev. A 237
- 238
- 240
- A-54 114078 Rev. A 241
- A-56 114078 Rev. A 243
- 244
- 245
- 245
- 247
- A-62 114078 Rev. A 249
- 114078 Rev. A A-63 250
- 252
- A-66 114078 Rev. A 253
- 255
- 255
- 256
- A-70 114078 Rev. A 257
- 258
- 259
- 114078 Rev. A A-73 260
- 261
- 114078 Rev. A A-75 262
- 263
- 263
- 114078 Rev. A A-77 264
- 266
- A-80 114078 Rev. A 267
- Appendix B 268
- Asynchronous Line Parameters 269
- ATM FRE-2 Line Parameters 269
- ATM ARE Line Parameters 270
- E1 Line Parameters 271
- FDDI Line Parameters 272
- HSSI Line Parameters 273
- LAPB Parameters 274
- MCE1 Line Parameters 274
- (continued) 275
- (continued) 276
- T1 Line Parameters 281
- Token Ring Line Parameters 281
- Multiline Parameters 281
- Table B-30. LRM Parameters 282
- Appendix C 284
- Setting Test Parameters 285
- 114078 Rev. A C-3 286
- Setting the BERT Alarm Type 287
- Setting the BERT Test Pattern 287
- Setting the Line Type 288
- C-6 114078 Rev. A 289
- Running Port Tests 290
- C-8 114078 Rev. A 291
- 114078 Rev. A C-9 292
- 114078 Rev. A Index-1 294
- 114078 Rev. A Index-3 296
- 114078 Rev. A Index-5 298
- 114078 Rev. A Index-7 300
Manuais e produtos relacionados com Redes Avaya Configuring Line Services
Redes Avaya BCM First Time Guia de Instalação
(14 páginas)
(14 páginas)
Redes Avaya IPv6 Manual do Utilizador
(162 páginas)
(162 páginas)
Redes Avaya L2TP Manual do Utilizador
(114 páginas)
(114 páginas)
Redes Avaya BCM450 Manual do Utilizador
(22 páginas)
(22 páginas)
Redes Avaya BSGX4e Guia do Utilizador
(206 páginas)
(206 páginas)
Redes Avaya a WAN Adapter Module in a BayStack ARN Router (114204 Rev. A) Manual do Utilizador
(34 páginas)
(34 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.093 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais