Avaya BCM 2.5 IP Telephony Guia de Configuração Página 36
- Página / 128
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
36 Chapter 3 Installing IP Telephones
P0937663 02.0
After you have configured a telephone, it attempts to connect to the Business Communications
Manager. The message ‘Locating Server’ appears on the display. If the connection is successful,
the message changes to ‘Connecting to Server’ after about 15 seconds.
The IP telephone is completely booted once the date/time string is displayed on the telephone. Do
not attempt to use the telephone while the string "Connecting to server" is displayed (initialization
of the telephone may take several minutes).
Troubleshooting an IP telephone
If the system is not properly configured, several messages can appear:
• SERVER: NO PORTS LEFT--The Business Communications Manager has run out of ports.
This message will remain on the display until a port becomes available and the telephone is
powered down then powered up.To obtain more ports, you may need to install additional
keycodes. See the Keycode Installation Guide.
• Invalid Server Address--The S1 is incorrectly configured with the IP address of a Business
Communications Manager network adapter other than the published IP address.
• NEW SET--The telephone has not been connected to the Business Communications Manager
before, and must be registered.
DEF GW Default Gateway on the network (i.e., the nearest router to the
telephone.
The router for IP address W.X.Y.Z is usually at W.X.Y.1)
If there are no routers between the telephone and the Business
Communications Manager network adaptor to which it is connected, (for
example a direct HUB connection), then enter the Published IP address
of the Business Communications Manager as the DEF GW.
If the IP telephone is not connected directly to the Published IP address
network adaptor, set the DEF GW to the IP address of the network
adaptor the telephone is connected to. For information on setting the
published IP address of the Business Communications Manager, see
“Setting the Published IP Address” on page 51.
S1 IP This is the Published IP address of the Business Communications
Manager.
S1 PORT Set this to 7000.
S1 ACTION Set this to 1.
S1 RETRY COUNT Set this to 255.
S2 IP This is the Published IP address of the Business Communications
Manager.
S2 PORT Set this to 7000.
S2 ACTION Set this to 1.
S2 RETRY COUNT Set this to 255.
- Business Communications 1
- Manager 2.5 1
- IP Telephony Configuration 1
- Trademarks 2
- Contents 3
- Chapter 4 4
- Chapter 5 5
- Appendix A 5
- Before you begin 13
- Symbols used in this guide 14
- Text conventions 14
- Acronyms 15
- UDP User Datagram Protocol 16
- WAN Wide Area Network 16
- Related publications 17
- How to get help 18
- Chapter 1 19
- Introduction 19
- The IP telephony network 20
- Chapter 1 Introduction 21 21
- Figure 1 Network diagram 21
- Telephones 22
- IP Network 22
- Key IP Telephony Concepts 23
- Jitter Buffer 24
- QoS routing 24
- Chapter 1 Introduction 25 25
- 26 Chapter 1 Introduction 26
- Chapter 2 27
- Prerequisites checklist 27
- Network assessment 28
- Resource Assessment 28
- Keycodes 29
- IP Telephones 30
- Chapter 3 31
- Installing IP Telephones 31
- Choosing a codec 33
- Choosing a Jitter Buffer 33
- Before Installing 34
- Manual Cfg DHCP(0 no, 1 yes) 35
- Configuring DHCP 38
- Figure 4 DHCP summary 39
- Figure 5 DHCP range 40
- Figure 6 IP Terminal status 41
- Figure 7 Configuration menu 42
- Figure 9 IP Terminal Status 43
- Download Pending 44
- Deregistering offline DNs 45
- Moving IP telephones 46
- H.323 devices 47
- 4 Click the Save button 49
- VoIP Trunk Configuration 51
- Configuring media parameters 53
- Configuring codecs 54
- Setting Silence Compression 54
- Setting Jitter Buffers 55
- Outgoing call configuration 56
- Figure 21 Trunk/Line data 57
- Figure 22 Line pool 58
- Configuring a remote gateway 59
- Configuring PSTN fallback 60
- Setting up a VoIP schedule 61
- Vo I P 62
- Configuring routes 63
- Figure 28 Route list 64
- Figure 29 Add route dialog 64
- Creating a destination code 65
- Figure 32 Normal schedule 66
- Configuring digits 67
- Activating the VoIP schedule 67
- Turning on QoS monitor 68
- Incoming call configuration 70
- Example configuration 71
- Making calls 74
- Connecting an i200X telephone 75
- Quality of Service Monitor 77
- Port settings 77
- Using firewalls 78
- Using a gatekeeper 80
- Gatekeeper call scenarios 82
- Typical applications 85
- MCDN functionality 86
- Networking 91
- Network Engineering 92
- Networking 93 93
- (64 kb/s) 93
- (5.3 kb/s) 93
- LAN Engineering Examples 95
- WAN engineering 96
- Setting Non-linear processing 96
- Networking 97 97
- Traceroute 97
- Enough link capacity 98
- Not enough link capacity 98
- Implementing the network 99
- Further network analysis 99
- Reduce link delay 100
- Reducing hop count 100
- Adjust the jitter buffer size 101
- Reduce packet errors 101
- Routing issues 102
- Silence compression 103
- Appendix B 103
- 104 Silence compression 104
- P0937663 02.0 104
- Silence compression 105 105
- 106 Silence compression 106
- Silence compression 107 107
- Comfort Noise 108
- Appendix C 109
- Network Performance Utilities 109
- Appendix D 111
- Interoperability 111
- Speech Path Setup Methods 112
- Media Path Redirection 112
- Gatekeeper 113
- Symbol Telephones 114
- Appendix E 115
- Quality of Service 115
- Measuring Intranet QoS 116
- Recording routes 117
- Adjustment for processing 118
- Late packets 118
- Quality of Service 119 119
- Traffic mix 120
- Network Quality of Service 121
- Packet loss 122
- Packet delay 122
- Delay variation (jitter) 123
- 124 Quality of Service 124
- Glossary 125
- 126 Glossary 126
Manuais e produtos relacionados com Gateways/controladores Avaya BCM 2.5 IP Telephony
(35 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais