Avaya Configuring Dial Services Manual do Utilizador Página 476
- Página / 552
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuring Dial Services
B-14
308621-14.00 Rev 00
Dial-on-Demand for an ISDN Network
Figure B-3 illustrates dial-on-demand service configured for an ISDN network. In
this configuration:
• The BLN is using a dual port MCT1 link module (port 2) for its PRI interface.
• The ISDN switch type is PRI 5ESS.
• The IP static route configurations are not listed for the Ethernet interfaces.
(Typically, there would be static routes.)
This example assumes the following:
• All BRI connections use a National ISDN 1 (NI1) switch.
• There is no incoming call filtering.
• Sending complete IEs are not used for call setup.
• The adaption rate is 64 Kb/s.
• CHAP is the PPP authentication protocol.
• IP is the only LAN protocol configured.
• The Ethernet segments shown in the network illustration are not configured.
• Only one phone number and SPID are used. (BRI lines usually have two
phone numbers and SPIDs.)
Figure B-3. Dial-on-Demand for an ISDN Network
ISDN
Router 1
Router 2
ISDN 1
.1
Local phone no: 4366666
Switch type: PRI 5ESS
CHAP local name: BLN
CHAP secret: ISDN
Local phone no: 4364444
Switch type: BRI NI1
CHAP local name: ASN
CHAP secret: ISDN
BLN
M
C
T
1
ASN
MCT1-port 2
.3
132.132.132.0
DS0024A
- Configuring Dial Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308621-14.00 Rev 00 10
- Before You Begin 25
- Text Conventions 26
- Set Trap Monitor Filters 27
- Acronyms 28
- Hard-Copy Technical Manuals 30
- How to Get Help 30
- Chapter 1 31
- Dial Services Overview 31
- How to Use This Guide 32
- Nortel Networks Dial Services 33
- Dial-on-Demand Service 35
- Terminating Demand Circuits 36
- Demand Lines and Pools 38
- Demand Circuit Protocols 40
- Dial Backup Service 44
- Activating the Backup Line 45
- Backup Circuit Protocols 46
- Backup Lines and Pools 50
- Bandwidth-on-Demand Service 52
- Terminating Secondary Lines 55
- Chapter 2 59
- Starting Dial Services 59
- Setting Up a Dial Service 60
- Appendix A of this guide 63
- (Figure 2-1) 63
- Configuring Line Pools 64
- • Configuring BRI Lines 66
- on page 2-9 66
- Configuring BRI Lines 67
- Adding ISDN Lines to a Pool 71
- Configuring Circuits 72
- Enabling a Protocol 76
- Specifying the Backup Mode 78
- Creating Bandwidth Circuits 80
- Specifying the Bandwidth Mode 81
- Chapter 3 91
- <parameter> 93
- DS0037A 97
- Configuring a Modem Interface 100
- Configuring an ISDN Interface 102
- Configuring PRI Lines 104
- Creating a Line Pool 105
- Adding Lines to the Pool 106
- <mode> 109
- Protocols for Backup Circuits 110
- <string> 111
- What to Do Next 114
- Chapter 4 115
- ISDN Overview 115
- ISDN Standards 116
- Primary Rate Interface 117
- D Channel 117
- Figure 4-3. LAPD Frame 118
- ISDN Interfaces 119
- Reference Points 120
- Chapter 5 123
- Implementation Notes 123
- Types of Authentication 124
- WAN Encryption Protocol 128
- Asynchronous PPP 128
- ISDN Services 132
- Incoming Call Filtering 138
- Rate Adaption 139
- Example 2 140
- Chapter 6 143
- Standby Circuits 144
- How Standby Circuits Work 145
- Callback 147
- Configuring Callback 148
- Demand Circuit Groups 149
- Static Routes 150
- Dial-Optimized Routing 151
- Traffic Filters 154
- Data Compression 155
- PPP Multilink 156
- Protocol Prioritization 157
- Chapter 7 159
- Bandwidth for Backup Circuits 160
- Chapter 8 165
- Multilink Fragmentation 168
- How BAP Works 169
- Chapter 9 175
- Customizing Line Pools 175
- Changing Pool IDs 176
- Deleting Pools 176
- Using the BCC 177
- Using Site Manager 177
- <integer> 178
- Disabling MRU Compliance 181
- Chapter 10 183
- Customizing Modem Lines 183
- Modifying the Line Priority 187
- Using Modem Factory Defaults 189
- 34 characters 196
- is enabled or disabled 198
- For example: 198
- Resetting the Modem Remotely 200
- Chapter 11 205
- Customizing ISDN Lines 205
- Modifying the Adaption Rate 213
- Configuring the TEI Type 216
- Configuring the TEI Value 217
- Modifying the BRI T4 Timer 221
- Changing the Circuit Name 224
- Modifying the MTU 224
- Chapter 12 229
- Customizing Demand Circuits 229
- Adding a Service Record 233
- Adding or Modifying PVCs 234
- Retrying the Connection 239
- <text-string> 245
- Setting the Inactivity Mode 250
- Configuring Standby Circuits 254
- <failback_mode> 256
- <action> 257
- Enabling Callback 259
- Deleting a Schedule 273
- Removing Demand Circuits 280
- Deleting Hot Standby Circuits 281
- Chapter 13 283
- Customizing Backup Circuits 283
- <ID_number> 285
- ID_number 285
- Specifying the Redial Count 299
- (continued) 300
- To remove backup service: 305
- Chapter 14 307
- Chapter 15 317
- Customizing Phone Lists 317
- Local Phone Lists 319
- Adding Phone Numbers 320
- Changing the Remote Pool Type 329
- To set the remote pool type: 330
- Enabling PRI Multirate 332
- can be one of the following: 341
- To create a local phone list: 341
- Chapter 16 345
- Customizing Caller Resolution 345
- Configuring the CHAP Secret 348
- Configuring the PAP Password 348
- Appendix A 353
- Site Manager Parameters 353
- Caution: 355
- Pool ID Parameter 356
- External Modem Parameters 361
- V.34 Modem Parameters 367
- ISDN Switch Parameters 372
- BRI Configuration Parameters 379
- Figure A-11 407
- Parameters 434
- Local Phone Number Parameters 442
- Appendix B 463
- Configuration Examples 463
- Dial-on-Demand with PPP 464
- Demand Circuit Configuration 469
- Configuration of Router 1 473
- Configuration of Router 2 474
- Backup Pool Configuration 491
- backup-line bri/3/2/1 497
- Appendix C 507
- BCC show Commands 507
- show dial backup circuits 508
- Online Help for show Commands 509
- Commands for Dial-on-Demand 510
- Demand Circuit Information 512
- <circuit_name> 516
- -caller 517
- -circuit 518
- Commands for Dial Backup 519
- Modem Commands 530
- Receive Errors 533
- Transmit Errors 533
- System Errors 533
- Appendix D 537
- Ordering PRI Lines 538
- Appendix E 539
- (continued) 541
Manuais e produtos relacionados com Manuais de software Avaya Configuring Dial Services
Manuais de software Avaya Configuring Interface and Router Redundancy Manual do Utilizador
(72 páginas)
(72 páginas)
Manuais de software Avaya Quick-Starting Routers and BNX Platforms Manual do Utilizador
(126 páginas)
(126 páginas)
Manuais de software Avaya Site Administration Reference Release 3.1 Manual do Utilizador
(178 páginas)
(178 páginas)
Manuais de software Avaya Quick-Starting Routers (308654-14.20 Rev 00) Manual do Utilizador
(134 páginas)
(134 páginas)
Manuais de software Avaya Configuring Interface and Router Redundancy Manual do Utilizador
(90 páginas)
(90 páginas)
Manuais de software Avaya BCM 3.6 Guia do Utilizador
(54 páginas)
(54 páginas)
Manuais de software Avaya IVR Guia de Configuração
(69 páginas)
(69 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.203 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais