Avaya Configuring WAN Line Services Manual do Utilizador Página 140
- Página / 246
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuring WAN Line Services
7-40 117021-A Rev. A
Setting the Signal Level (MCT1 Only)
By default, the T1 transmit power level is 0.0 dB. Specify a decibel level from
-15 dB to 1.5 dB, according to the length of the cable or as determined by the
carrier. Refer to “Setting the Signal Level,” earlier in this chapter, for more
information.
Enabling or Disabling the International Bit (MCE1 Only)
By default, MCE1 does not use the international bit in E1 frames. Enable or
disable use of the International Bit for testing an MCE1 interface.
Running Port Tests
To run MCE1 or MCT1 port tests:
1. Set the test parameters in the Port Actions window.
Refer to the “Setting Port Test Parameters” section.
2. Click on Apply.
3. To start a test, click on the appropriate Send Command.
T
able 7-3 describes the BERT test commands you can send on any MCT1 or
MCE1 port. T
able 7-4 describes the loopback commands you can send on an
MCT1 port only.
Note: Port tests affect all logical lines associated with that port.
Table 7-3. Send Commands for MCE1 and MCT1 Port Tests
Send Command Function
Reset BERT Counters Resets all counters to 0
Insert 1 Error Inserts a single (nonrepeating) error into the bit stream
Insert 1 Error/1K Inserts a deliberate error into every thousandth position in the
bit stream
Insert 1 Error/1M Inserts a deliberate error into every millionth position in the bit
stream
Disable Insert Error Stops the insertion of deliberate errors into the bit stream
- Configuring WAN 1
- Line Services 1
- USA Requirements Only 3
- Canada Requirements Only 5
- T1 Service 8
- Bay Networks Software License 9
- (continued) 10
- Contents 11
- About This Guide 23
- Before You Begin 24
- Conventions 24
- Acronyms 25
- For More Information 28
- Chapter 1 29
- Getting Started 29
- 1-2 117021-A Rev. A 30
- 1-4 117021-A Rev. A 32
- Configuring ATM Services 33
- Token Ring Services 33
- Chapter 2 35
- 2-2 117021-A Rev. A 36
- 117021-A Rev. A 2-3 37
- 2-4 117021-A Rev. A 38
- Setting the BofL Timeout 39
- Setting the MTU 39
- Configuring Clocking Signals 40
- 117021-A Rev. A 2-7 41
- Setting the Signal Mode 42
- 117021-A Rev. A 2-9 43
- Setting Minimum Frame Spacing 44
- 117021-A Rev. A 2-11 45
- 2-12 117021-A Rev. A 46
- Setting the CRC Size 47
- Setting the Signaling Method 48
- Setting the Line Coding 49
- Configuring KG84A Security 50
- 117021-A Rev. A 2-17 51
- 2-18 117021-A Rev. A 52
- Setting the Retry Count 53
- Setting the Link Idle Timer 53
- Setting the Cable Type 54
- Setting the Retry Timer 55
- Setting the Hold Down Time 56
- Setting a Priority 56
- 117021-A Rev. A 2-23 57
- Setting the IFTF Pattern 58
- 117021-A Rev. A 2-25 59
- 117021-A Rev. A 2-27 61
- Setting the Station Type 62
- Setting the Control Field 62
- Setting the Window Size 63
- Setting the N2 Retry Count 63
- 2-30 117021-A Rev. A 64
- Setting the Link Setup Action 65
- Viewing the WAN Protocol 66
- Chapter 3 67
- Asynchronous Services 67
- 3-2 117021-A Rev. A 68
- Setting the Baud Rate 69
- Setting the Idle Timer 69
- 3-4 117021-A Rev. A 70
- Setting the Remote IP Address 71
- Specifying the Remote Port 71
- Specifying the Local Port 71
- 3-6 117021-A Rev. A 72
- 117021-A Rev. A 3-7 73
- Chapter 4 75
- 4-2 117021-A Rev. A 76
- 2. Click on Edit DSU/CSU 76
- Setting the Option Mode 77
- 4-4 117021-A Rev. A 78
- 117021-A Rev. A 4-5 79
- 4-6 117021-A Rev. A 80
- Loopback Test Modes 81
- 4-8 117021-A Rev. A 82
- Figure 4-7. Analog Loopback 82
- Figure 4-8. Pattern-2047 Test 83
- Chapter 5 85
- Configuring HSSI Services 85
- Configuring BofL Messages 86
- 5-4 117021-A Rev. A 88
- Chapter 6 91
- Configuring E1 or T1 Services 91
- 6-2 117021-A Rev. A 92
- Setting the T1 Frame Type 93
- 6-4 117021-A Rev. A 94
- Figure 6-2. Bipolar Format 94
- Specifying Line Buildout 95
- Editing E1 Services 97
- 6-8 117021-A Rev. A 98
- Setting the Clock Source 99
- Assigning Channel Functions 100
- Chapter 7 101
- About MCE1 and MCT1 Services 102
- 117021-A Rev. A 7-3 103
- Setting the Clock Parameters 104
- 7-6 117021-A Rev. A 106
- 4. Click on OK 106
- 5. Continue with 106
- Configuring WAN Line Services 106
- 117021-A Rev. A 7-7 107
- 7-8 117021-A Rev. A 108
- 117021-A Rev. A 7-9 109
- 7-10 117021-A Rev. A 110
- 117021-A Rev. A 7-11 111
- 7-12 117021-A Rev. A 112
- 117021-A Rev. A 7-13 113
- 7-14 117021-A Rev. A 114
- 117021-A Rev. A 7-15 115
- Configuring a DS0A Connection 116
- 117021-A Rev. A 7-17 117
- BYS0060A 117
- 117021-A Rev. A 118
- Defining Logical Lines 119
- Click on Add 120
- 117021-A Rev. A 7-21 121
- Chapter 8 123
- 7-24 117021-A Rev. A 124
- 3. Click on Apply 124
- 117021-A Rev. A 7-25 125
- 7-26 117021-A Rev. A 126
- 117021-A Rev. A 7-27 127
- 7-28 117021-A Rev. A 128
- 117021-A Rev. A 7-29 129
- 7-30 117021-A Rev. A 130
- Assigning Timeslots 131
- 7-32 117021-A Rev. A 132
- 117021-A Rev. A 7-33 133
- 7-34 117021-A Rev. A 134
- 117021-A Rev. A 7-35 135
- Testing MCE1 and MCT1 Lines 136
- Setting Port Test Parameters 137
- 7-38 117021-A Rev. A 138
- 117021-A Rev. A 7-39 139
- Running Port Tests 140
- 117021-A Rev. A 7-43 143
- Running Logical Line Tests 144
- Click on Done 145
- Configuring Multiline Services 147
- 8-2 117021-A Rev. A 148
- Multiline Example 149
- Software Considerations 150
- 117021-A Rev. A 8-7 153
- 8-8 117021-A Rev. A 154
- 117021-A Rev. A 8-9 155
- 8-10 117021-A Rev. A 156
- 117021-A Rev. A 8-11 157
- 117021-A Rev. A 8-13 159
- 8-14 117021-A Rev. A 160
- 117021-A Rev. A 8-15 161
- Appendix A 163
- Asynchronous Line Parameters 164
- 117021-A Rev. A A-3 165
- A-4 117021-A Rev. A 166
- 117021-A Rev. A A-5 167
- A-6 117021-A Rev. A 168
- DSU/CSU Parameters 169
- 170
- 170
- E1 Line Parameters 171
- 172
- 172
- 173
- HSSI Line Parameters 174
- 117021-A Rev. A A-13 175
- A-14 117021-A Rev. A 176
- 177
- LAPB Parameters 178
- 179
- A-18 117021-A Rev. A 180
- 117021-A Rev. A A-19 181
- 182
- 117021-A Rev. A A-21 183
- A-22 117021-A Rev. A 184
- MCE1 Port Parameters 185
- 186
- 188
- 117021-A Rev. A A-27 189
- MCT1 Port Parameters 190
- 117021-A Rev. A A-29 191
- A-30 117021-A Rev. A 192
- 193
- 195
- 197
- 199
- 201
- Synchronous Line Parameters 204
- 207
- 207
- 208
- 209
- A-48 117021-A Rev. A 210
- A-50 117021-A Rev. A 212
- 117021-A Rev. A A-51 213
- 117021-A Rev. A A-53 215
- A-54 117021-A Rev. A 216
- 218
- 218
- 219
- 220
- 221
- T1 Line Parameters 222
- 223
- 225
- A-64 117021-A Rev. A 226
- Appendix B 227
- B-2 117021-A Rev. A 228
- MCE1 Line Parameters 230
- MCT1 Line Parameters 232
- B-8 117021-A Rev. A 234
- B-10 117021-A Rev. A 236
- Multiline Parameters 237
- Glossary 239
- 117021-A Rev. A Index-1 241
- 117021-A Rev. A Index-3 243
- 117021-A Rev. A Index-5 245
Manuais e produtos relacionados com Redes Avaya Configuring WAN Line Services
Redes Avaya R2 Guia de Instalação
(147 páginas)
(147 páginas)
Redes Avaya BayRS, BCC, and Site Manager Software Version 15.1.0.0 Fixed Anomalies Manual do Utilizador
(26 páginas)
(26 páginas)
Redes Avaya BayRs Version 12.20 Aviso
(54 páginas)
(54 páginas)
Redes Avaya BCM50 Guia de Resolução de Problemas
(92 páginas)
(92 páginas)
Redes Avaya DHCP BCM Rls 6.0 Manual do Utilizador
(26 páginas)
(26 páginas)
Redes Avaya E1/FE1 Manual do Utilizador
(42 páginas)
(42 páginas)
Redes Avaya v8.0 Manual do Utilizador
(23 páginas)
(23 páginas)
Redes Avaya E1 Manual do Utilizador
(52 páginas)
(52 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais