Avaya Configuring WAN Line Services Manual do Utilizador
Consulte online ou descarregue Manual do Utilizador para Redes Avaya Configuring WAN Line Services. Avaya Configuring WAN Line Services User's Manual Manual do Utilizador
- Página / 246
- Índice
- MARCADORES
- Configuring WAN 1
- Line Services 1
- USA Requirements Only 3
- Canada Requirements Only 5
- T1 Service 8
- Bay Networks Software License 9
- (continued) 10
- Contents 11
- About This Guide 23
- Before You Begin 24
- Conventions 24
- Acronyms 25
- For More Information 28
- Chapter 1 29
- Getting Started 29
- 1-2 117021-A Rev. A 30
- 1-4 117021-A Rev. A 32
- Configuring ATM Services 33
- Token Ring Services 33
- Chapter 2 35
- 2-2 117021-A Rev. A 36
- 117021-A Rev. A 2-3 37
- 2-4 117021-A Rev. A 38
- Setting the BofL Timeout 39
- Setting the MTU 39
- Configuring Clocking Signals 40
- 117021-A Rev. A 2-7 41
- Setting the Signal Mode 42
- 117021-A Rev. A 2-9 43
- Setting Minimum Frame Spacing 44
- 117021-A Rev. A 2-11 45
- 2-12 117021-A Rev. A 46
- Setting the CRC Size 47
- Setting the Signaling Method 48
- Setting the Line Coding 49
- Configuring KG84A Security 50
- 117021-A Rev. A 2-17 51
- 2-18 117021-A Rev. A 52
- Setting the Retry Count 53
- Setting the Link Idle Timer 53
- Setting the Cable Type 54
- Setting the Retry Timer 55
- Setting the Hold Down Time 56
- Setting a Priority 56
- 117021-A Rev. A 2-23 57
- Setting the IFTF Pattern 58
- 117021-A Rev. A 2-25 59
- 117021-A Rev. A 2-27 61
- Setting the Station Type 62
- Setting the Control Field 62
- Setting the Window Size 63
- Setting the N2 Retry Count 63
- 2-30 117021-A Rev. A 64
- Setting the Link Setup Action 65
- Viewing the WAN Protocol 66
- Chapter 3 67
- Asynchronous Services 67
- 3-2 117021-A Rev. A 68
- Setting the Baud Rate 69
- Setting the Idle Timer 69
- 3-4 117021-A Rev. A 70
- Setting the Remote IP Address 71
- Specifying the Remote Port 71
- Specifying the Local Port 71
- 3-6 117021-A Rev. A 72
- 117021-A Rev. A 3-7 73
- Chapter 4 75
- 4-2 117021-A Rev. A 76
- 2. Click on Edit DSU/CSU 76
- Setting the Option Mode 77
- 4-4 117021-A Rev. A 78
- 117021-A Rev. A 4-5 79
- 4-6 117021-A Rev. A 80
- Loopback Test Modes 81
- 4-8 117021-A Rev. A 82
- Figure 4-7. Analog Loopback 82
- Figure 4-8. Pattern-2047 Test 83
- Chapter 5 85
- Configuring HSSI Services 85
- Configuring BofL Messages 86
- 5-4 117021-A Rev. A 88
- Chapter 6 91
- Configuring E1 or T1 Services 91
- 6-2 117021-A Rev. A 92
- Setting the T1 Frame Type 93
- 6-4 117021-A Rev. A 94
- Figure 6-2. Bipolar Format 94
- Specifying Line Buildout 95
- Editing E1 Services 97
- 6-8 117021-A Rev. A 98
- Setting the Clock Source 99
- Assigning Channel Functions 100
- Chapter 7 101
- About MCE1 and MCT1 Services 102
- 117021-A Rev. A 7-3 103
- Setting the Clock Parameters 104
- 7-6 117021-A Rev. A 106
- 4. Click on OK 106
- 5. Continue with 106
- Configuring WAN Line Services 106
- 117021-A Rev. A 7-7 107
- 7-8 117021-A Rev. A 108
- 117021-A Rev. A 7-9 109
- 7-10 117021-A Rev. A 110
- 117021-A Rev. A 7-11 111
- 7-12 117021-A Rev. A 112
- 117021-A Rev. A 7-13 113
- 7-14 117021-A Rev. A 114
- 117021-A Rev. A 7-15 115
- Configuring a DS0A Connection 116
- 117021-A Rev. A 7-17 117
- BYS0060A 117
- 117021-A Rev. A 118
- Defining Logical Lines 119
- Click on Add 120
- 117021-A Rev. A 7-21 121
- Chapter 8 123
- 7-24 117021-A Rev. A 124
- 3. Click on Apply 124
- 117021-A Rev. A 7-25 125
- 7-26 117021-A Rev. A 126
- 117021-A Rev. A 7-27 127
- 7-28 117021-A Rev. A 128
- 117021-A Rev. A 7-29 129
- 7-30 117021-A Rev. A 130
- Assigning Timeslots 131
- 7-32 117021-A Rev. A 132
- 117021-A Rev. A 7-33 133
- 7-34 117021-A Rev. A 134
- 117021-A Rev. A 7-35 135
- Testing MCE1 and MCT1 Lines 136
- Setting Port Test Parameters 137
- 7-38 117021-A Rev. A 138
- 117021-A Rev. A 7-39 139
- Running Port Tests 140
- 117021-A Rev. A 7-43 143
- Running Logical Line Tests 144
- Click on Done 145
- Configuring Multiline Services 147
- 8-2 117021-A Rev. A 148
- Multiline Example 149
- Software Considerations 150
- 117021-A Rev. A 8-7 153
- 8-8 117021-A Rev. A 154
- 117021-A Rev. A 8-9 155
- 8-10 117021-A Rev. A 156
- 117021-A Rev. A 8-11 157
- 117021-A Rev. A 8-13 159
- 8-14 117021-A Rev. A 160
- 117021-A Rev. A 8-15 161
- Appendix A 163
- Asynchronous Line Parameters 164
- 117021-A Rev. A A-3 165
- A-4 117021-A Rev. A 166
- 117021-A Rev. A A-5 167
- A-6 117021-A Rev. A 168
- DSU/CSU Parameters 169
- 170
- 170
- E1 Line Parameters 171
- 172
- 172
- 173
- HSSI Line Parameters 174
- 117021-A Rev. A A-13 175
- A-14 117021-A Rev. A 176
- 177
- LAPB Parameters 178
- 179
- A-18 117021-A Rev. A 180
- 117021-A Rev. A A-19 181
- 182
- 117021-A Rev. A A-21 183
- A-22 117021-A Rev. A 184
- MCE1 Port Parameters 185
- 186
- 188
- 117021-A Rev. A A-27 189
- MCT1 Port Parameters 190
- 117021-A Rev. A A-29 191
- A-30 117021-A Rev. A 192
- 193
- 195
- 197
- 199
- 201
- Synchronous Line Parameters 204
- 207
- 207
- 208
- 209
- A-48 117021-A Rev. A 210
- A-50 117021-A Rev. A 212
- 117021-A Rev. A A-51 213
- 117021-A Rev. A A-53 215
- A-54 117021-A Rev. A 216
- 218
- 218
- 219
- 220
- 221
- T1 Line Parameters 222
- 223
- 225
- A-64 117021-A Rev. A 226
- Appendix B 227
- B-2 117021-A Rev. A 228
- MCE1 Line Parameters 230
- MCT1 Line Parameters 232
- B-8 117021-A Rev. A 234
- B-10 117021-A Rev. A 236
- Multiline Parameters 237
- Glossary 239
- 117021-A Rev. A Index-1 241
- 117021-A Rev. A Index-3 243
- 117021-A Rev. A Index-5 245
Resumo do Conteúdo
Part No. 117021-A Rev. AMay 1997Router Software Version 11.02Site Manager Software Version 5.02 Configuring WAN Line Services
x 117021-A Rev. A Bay Networks Software License (continued) 9. Licensee shall not reverse assemble, reverse compile, or in any way reverse engineer
Configuring WAN Line Services6-10 117021-A Rev. AYou can set the Clock Mode on this interface.Assigning Channel FunctionsUnless you change the default
117021-A Rev. A 7-1 Chapter 7Configuring MCE1 and MCT1 ServicesThe sections of this chapter describe the line services for Multichannel E1 (MCE1) or Mu
Configuring WAN Line Services7-2 117021-A Rev. AAbout MCE1 and MCT1 ServicesBay Networks supports multichannel E1 and T1 circuits on a router that con
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-3 Configuring MCE1 and MCT1 PortsComplete the steps in this section to enable MCE1 or MCT1 services
Configuring WAN Line Services7-4 117021-A Rev. ASelect NONPRI to indicate that all the lines have a permanent circuit number and are for leased lines,
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-5 • Configured Single- or Dual-Port MCE1 or MCT1 link or net moduleClick on the CLOCK connector for
Configuring WAN Line Services7-6 117021-A Rev. A3. Set the secondary (backup) clock source, using the same options.The router uses the secondary clock
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-7 Figure 7-2. MCE1 Port Parameters WindowEnabling or Disabling the MCE1 PortAn MCE1 port is enable
Configuring WAN Line Services7-8 117021-A Rev. ASetting the MCE1 Line Coding E1 uses bipolar format for signals. In bipolar format, alternating positi
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-9 Enabling or Disabling the International BitBy default, the MCE1 interface does not use the inter
117021-A Rev. A xi Contents About This Guide Before You Begin ...
Configuring WAN Line Services7-10 117021-A Rev. AFigure 7-3. MCT1 Port Parameters WindowThe MCT1 port parameters apply to each of the DS0 channels (ti
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-11 Setting the MCT1 Line TypeSelect one of the following line types (framing formats) for your T1
Configuring WAN Line Services7-12 117021-A Rev. ASet the line coding for this MCT1 interface.Setting the Signal LevelThe Signal Level parameter specifi
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-13 Setting the Alarm Threshold Clear TimeBy default, the clear time for performance failure condit
Configuring WAN Line Services7-14 117021-A Rev. AEnabling or Disabling Loopback RequestsBy default, the MCT1 interface accepts requests to go into loo
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-15 Setting the Source of Accept Performance MessagesOn DMCT1 net modules and QMCT1 or QMCT1 w/ DS0
Configuring WAN Line Services7-16 117021-A Rev. ASetting the Secondary Clock SourceOn DMCT1 net modules and QMCT1 or QMCT1 w/ DS0A link modules only,
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-17 • The NRZI type setting for-- The host side if the line encoding settings of the host and CPE d
Configuring WAN Line Services7-18 117021-A Rev. ATo configure a T1 connection to an unconfigured port on a QMCT1 DS0A link module to carry SDLC traffic:1
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-19 13.Scroll to Rate Adaption and set the value to 9.6 or 19.2 Kb/s. 14. Scroll to the NRZI Enable
xii 117021-A Rev. A Specifying the Link Level Protocol ...2-10Setting the Tra
Configuring WAN Line Services7-20 117021-A Rev. AFigure 7-5. Logical Lines Window before Defining a Circuit (MCT1 Example)2.Click on Add.The Add Circui
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-21 Figure 7-6. Add Circuit Window (MCE1 Example)3.Name the logical line in the Circuit Name box.Yo
Configuring WAN Line Services7-22 117021-A Rev. AFigure 7-8. Default Circuit Name for ASN Net Modules4.Click on OK.The WAN Protocols window appears. 5
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-23 Figure 7-9. Logical Lines Window with One Circuit Defined (MCE1 Example)7.Repeat Steps 2 to 6 fo
Configuring WAN Line Services7-24 117021-A Rev. ACustomizing Logical Line ParametersAfter you finish adding the logical lines for a non-PRI interface,
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-25 Enabling or Disabling the Logical Line The logical line is enabled by default. You can disable
Configuring WAN Line Services7-26 117021-A Rev. AViewing the Configured WAN ProtocolYou can view which WAN protocol is configured on this logical line.
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-27 Setting the Remote HDLC AddressSpecify the 1-byte HDLC address of the remote MCE1 interface as
Configuring WAN Line Services7-28 117021-A Rev. ASelect the line rate adaptation for this logical line. Setting the Interframe Time Fill PatternThe ro
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-29 Enabling or Disabling Remote Loopback DetectionSetting Remote Loopback Detection enables or dis
117021-A Rev. A xiiiEditing LAPB Protocol Services ...2-25LAPB Imple
Configuring WAN Line Services7-30 117021-A Rev. ASee “Testing MCE1 and MCT1 Lines,” later in this chapter, for more information about running BERT tes
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-31 When enabled, the NRZI Enable parameter specifies nonreturn to zero inverted (NRZI) line encodin
Configuring WAN Line Services7-32 117021-A Rev. AFigure 7-10. Timeslots Window (MCT1 Example)This window graphically represents the timeslots (31 for
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-33 Figure 7-11. Assigning a Timeslot (MCE1 Example)4.Select the logical line to which you want to
Configuring WAN Line Services7-34 117021-A Rev. AConfiguring ISDN PRI B-ChannelsISDN Primary Rate Interface (PRI) software eliminates the need for an e
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-35 Figure 7-13. MCE1 Timeslots Window (ISDN PRI Configurations)3.Click on a timeslot to assign.4. S
Configuring WAN Line Services7-36 117021-A Rev. A9. Click on Apply.10. Click on Done.The Configuration Manager window appears.Testing MCE1 and MCT1 Lin
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-37 BERT statistics show the results of your test actions. You can view BERT statistics using the S
Configuring WAN Line Services7-38 117021-A Rev. A• Setting the Line Type• Setting FDL Options (MCT1 Only)• Setting the Signal Level (MCT1 Only)• Enabl
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-39 Setting the Line Coding MethodHow you set line coding depends on whether you are testing an MCE
xiv 117021-A Rev. A Chapter 4Configuring BayStack DSU/CSU Services Configuring DSU/CSU Services ...
Configuring WAN Line Services7-40 117021-A Rev. ASetting the Signal Level (MCT1 Only)By default, the T1 transmit power level is 0.0 dB. Specify a deci
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-41 In payload loopback, the signal loops through the T1 framer before the received signal is loope
Configuring WAN Line Services7-42 117021-A Rev. ASetting Logical Line Test ParametersOn DMCT1 net modules, QMCT1 link modules, and QMCT1 w/ DS0A link
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-43 6.After setting a parameter, click on Apply.7. Click on Done when you are finished setting line
Configuring WAN Line Services7-44 117021-A Rev. AEnabling Fractional Loopback RequestsTo enable channel-based loopback testing on a QMCT1 or QMCT1 w/
Configuring MCE1 and MCT1 Services117021-A Rev. A 7-45 4.Repeat Step 3 for each test you want to run.5. Click on Done. Table 7-5. Send Commands for Lo
117021-A Rev. A 8-1 Chapter 8Configuring Multiline ServicesThis chapter describes how to configure multiline services:• Overview of Multiline Configurati
Configuring WAN Line Services8-2 117021-A Rev. AThe data paths that form a multiline circuit must share the same bandwidth, MTU, and encapsulation met
Configuring Multiline Services117021-A Rev. A 8-3 Benefits of a Multiline ConfigurationUsing a multiline configuration rather than a single path provides
117021-A Rev. A xvD4 Format ...6-3ESF Format
Configuring WAN Line Services8-4 117021-A Rev. ASoftware ConsiderationsThis section provides notes or hints for operating multiline services with the
Configuring Multiline Services117021-A Rev. A 8-5 Configuring Multiline ServicesThe method you use to configure a multiline circuit depends on the types
Configuring WAN Line Services8-6 117021-A Rev. AFigure 8-3. Add Circuit WindowAdding Physical Lines to a CircuitThe data paths that form a multiline c
Configuring Multiline Services117021-A Rev. A 8-7 Figure 8-4. Circuit Definition Window4.Click on the connectors that you are adding to the circuit.Sit
Configuring WAN Line Services8-8 117021-A Rev. AFigure 8-5. Change Lines Menu OptionThe lines now form one circuit. The default traffic distribution me
Configuring Multiline Services117021-A Rev. A 8-9 Changing the Traffic Distribution MethodAll multiline circuits, by default, distribute traffic using a
Configuring WAN Line Services8-10 117021-A Rev. AAddress-based SelectionIf you choose address-based selection, the router determines the appropriate d
Configuring Multiline Services117021-A Rev. A 8-11 Grouping Logical Lines into a Multiline CircuitYou can group as many as 31 MCE1 logical lines and 2
Configuring WAN Line Services8-12 117021-A Rev. A3. Click on Cancel.Clicking on Cancel creates an unused logical line.The MCE1/MCT1 Logical Lines wind
Configuring Multiline Services117021-A Rev. A 8-13 2.Click on OK to create the circuit.The WAN Protocols window appears.3. Select the protocol for thi
xvi 117021-A Rev. A Setting the Alarm Threshold Time ...7-12Setting the Alarm Thres
Configuring WAN Line Services8-14 117021-A Rev. AIn Figure 8-8, the circuit is defined for logical line 5, and is called MCE1-22-5. For information abo
Configuring Multiline Services117021-A Rev. A 8-15 7.Select and hold down the logical line number (Figure 8-11).The Select Logical Lines window displa
Configuring WAN Line Services8-16 117021-A Rev. A10. Click on Circuit to display the Circuit Definition window again.11. Repeat Steps 6 through 8.12. S
117021-A Rev. A A-1 Appendix ASite Manager WAN Line Services ParametersThe following sections in this appendix contain reference information about Sit
Configuring WAN Line ServicesA-2 117021-A Rev. AAsynchronous Line ParametersOn a Bay Networks AN or ANH router only, the Configuration Manager displays
Site Manager WAN Line Services Parameters117021-A Rev. A A-3 Parameter: Remote IP AddrPath: COM Connector > Edit Line > Edit Asynchronous Parame
Configuring WAN Line ServicesA-4 117021-A Rev. AParameter: Baud Rate Path: COM Connector > Edit Line > Edit Asynchronous ParametersDefault: 9600
Site Manager WAN Line Services Parameters117021-A Rev. A A-5 Parameter: TCP KeepAlive Path: COM Connector > Edit Line > Edit Asynchronous Parame
Configuring WAN Line ServicesA-6 117021-A Rev. AParameter: Cfg TxQ Length Path: COM Connector > Edit Line > Edit Asynchronous ParametersDefault:
Site Manager WAN Line Services Parameters117021-A Rev. A A-7 DSU/CSU ParametersOn a BayStack AN, ANH, or ARN router only, you access the DSU/CSU Line
117021-A Rev. A xviiSetting Port Test Parameters ...7-37Enabling or Di
Configuring WAN Line ServicesA-8 117021-A Rev. AParameter: 64K Transmit MonitorPath: COM Connector > Edit DSU/CSU > Edit DSU CSU ParametersDefau
Site Manager WAN Line Services Parameters117021-A Rev. A A-9 E1 Line ParametersYou access the E1 Line Parameters from the Configuration Manager.Paramet
Configuring WAN Line ServicesA-10 117021-A Rev. AParameter: HDB3S SupportPath: E1 Connector > Edit Line > Edit E1 ParametersDefault: EnableOptio
Site Manager WAN Line Services Parameters117021-A Rev. A A-11 Parameter: Mini DacsPath: E1 Connector > Edit Line > Edit E1 ParametersDefault: Id
Configuring WAN Line ServicesA-12 117021-A Rev. AHSSI Line ParametersYou access the HSSI Line Parameters from the Configuration Manager.Parameter: Enab
Site Manager WAN Line Services Parameters117021-A Rev. A A-13 Parameter: BofL FrequencyPath: HSSI Connector > Edit Line > Edit HSSI ParametersDe
Configuring WAN Line ServicesA-14 117021-A Rev. AParameter: Transmission InterfacePath: HSSI Connector > Edit Line > Edit HSSI ParametersDefault
Site Manager WAN Line Services Parameters117021-A Rev. A A-15 Parameter: CRC SizePath: HSSI Connector > Edit Line > Edit HSSI ParametersDefault:
Configuring WAN Line ServicesA-16 117021-A Rev. ALAPB ParametersWhen you edit an Octal Sync link module line, or any synchronous line on Bay Networks
Site Manager WAN Line Services Parameters117021-A Rev. A A-17 Parameter: Control FieldPath: COM Connector for X.25 Interface > Edit Line > LAPB
xviii 117021-A Rev. A Appendix ASite Manager WAN Line Services Parameters Asynchronous Line Parameters ...
Configuring WAN Line ServicesA-18 117021-A Rev. AParameter: Max N2 RetriesPath: COM Connector for X.25 Interface > Edit Line > LAPB > Edit LA
Site Manager WAN Line Services Parameters117021-A Rev. A A-19 Parameter: Max T2 Acknowledge Timer (seconds)Path: COM Connector for X.25 Interface >
Configuring WAN Line ServicesA-20 117021-A Rev. AParameter: Initiate Link Setup Action Path: COM Connector for X.25 Interface > Edit Line > LAPB
Site Manager WAN Line Services Parameters117021-A Rev. A A-21 Parameter: WAN ProtocolPath: COM Connector for X.25 Interface > Edit Line > LAPB &
Configuring WAN Line ServicesA-22 117021-A Rev. AMCE1 Port Application and Clock ParametersParameter: Port Application ModePath: Unconfigured MCE1 Conn
Site Manager WAN Line Services Parameters117021-A Rev. A A-23 MCE1 Port ParametersYou can access the MCE1 port parameters from the Configuration Manage
Configuring WAN Line ServicesA-24 117021-A Rev. AParameter: Line TypePath: MCE1 Connector > Edit Logical Lines > Port Details > MCE1 Port Par
Site Manager WAN Line Services Parameters117021-A Rev. A A-25 Parameter: Setup Alarm Threshold (seconds)Path: MCE1 Connector > Edit Logical Lines &
Configuring WAN Line ServicesA-26 117021-A Rev. AMCT1 Port Application and Clock ParametersParameter: Line ImpedancePath: ASN MCE1 Connector > Edit
Site Manager WAN Line Services Parameters117021-A Rev. A A-27 Parameter: Primary Clock Path: MCT1 CLOCK Connector > Edit Slot x DS1/E1 Clock Parame
117021-A Rev. A xix Figures Figure 1-1. Configuration Manager Window ...1-2Figure 1-2. Cir
Configuring WAN Line ServicesA-28 117021-A Rev. AMCT1 Port ParametersYou access the MCT1 port line parameters from the Configuration Manager.Parameter:
Site Manager WAN Line Services Parameters117021-A Rev. A A-29 Parameter: Line CodingPath: MCT1 Connector > Edit Logical Lines > Port Details >
Configuring WAN Line ServicesA-30 117021-A Rev. AParameter: Signal Level (dB)Path: MCT1 Connector > Edit Logical Lines > Port Details > MCT1
Site Manager WAN Line Services Parameters117021-A Rev. A A-31 Parameter: Clear Alarm Threshold (seconds)Path: MCT1 Connector > Edit Logical Lines &
Configuring WAN Line ServicesA-32 117021-A Rev. AParameter: Remote FDL HDLC Address ModePath: MCT1 Connector > Edit Logical Lines > Port Details
Site Manager WAN Line Services Parameters117021-A Rev. A A-33 QMCT1 and DMCT1 Port ParametersIn addition to the parameters in the previous section, th
Configuring WAN Line ServicesA-34 117021-A Rev. AParameter: Accept Perf Measurement CR AddrPath: QMCT1 Connector > Edit Logical Lines > Port Det
Site Manager WAN Line Services Parameters117021-A Rev. A A-35 MCE1 and MCT1 Logical Line ParametersYou access the MCE1 and MCT1 logical line parameter
Configuring WAN Line ServicesA-36 117021-A Rev. AParameter: Breath of Life (BofL) Enable/DisablePath: Configured MCE1 or MCT1 Connector > MCE1/T1 Lo
Site Manager WAN Line Services Parameters117021-A Rev. A A-37 Parameter: WAN ProtocolPath: Configured MCE1 or MCT1 Connector > MCE1/T1 Logical Lines
ii 117021-A Rev. A4401 Great America Parkway 8 Federal StreetSanta Clara, CA 95054 Billerica, MA 01821 Copyright © 1988–1997 Bay Networks, Inc. All r
xx 117021-A Rev. A Figure 7-4. SDLC Connection via Frame Relay over T1 Lines ...7-17Figure 7-5. Logical Lines Window b
Configuring WAN Line ServicesA-38 117021-A Rev. AParameter: Remote HDLC AddressPath: Configured MCE1 or MCT1 Connector > MCE1/T1 Logical LinesDefaul
Site Manager WAN Line Services Parameters117021-A Rev. A A-39 Parameter: Interframe Time Fill CharacterPath: Configured MCE1 or MCT1 Connector > MCE
Configuring WAN Line ServicesA-40 117021-A Rev. AParameter: Remote Loopback DetectionPath: Configured MCE1 or MCT1 Connector > MCE1/T1 Logical Lines
Site Manager WAN Line Services Parameters117021-A Rev. A A-41 Parameter: Accept Fractional Loopback CodePath: Configured QMCT1 Connector (in Dynamic Mo
Configuring WAN Line ServicesA-42 117021-A Rev. ASynchronous Line ParametersYou access the synchronous line parameters from the Configuration Manager.P
Site Manager WAN Line Services Parameters117021-A Rev. A A-43 Parameter: BofLPath: COM Connector > Edit Line > Edit Sync ParametersDefault: Enab
Configuring WAN Line ServicesA-44 117021-A Rev. AParameter: MTUPath: COM Connector > Edit Line > Edit Sync ParametersDefault: 1600 bytesOptions:
Site Manager WAN Line Services Parameters117021-A Rev. A A-45 Parameter: Clock SourcePath: COM Connector > Edit Line > Edit Sync ParametersDefau
Configuring WAN Line ServicesA-46 117021-A Rev. AParameter: Signal ModePath: COM Connector > Edit Line > Edit Sync ParametersDefault: Balanced O
Site Manager WAN Line Services Parameters117021-A Rev. A A-47 Parameter: Burst CountPath: COM Connector > Edit Line > Edit Sync ParametersDefaul
117021-A Rev. A xxi Tables Table 1-1. Site Manager Abbreviations for Circuit Types ...1-3Table 7-1. MCE1 and
Configuring WAN Line ServicesA-48 117021-A Rev. AParameter: Retry CountPath: COM Connector > Edit Line > Edit Sync ParametersDefault: 16 attempt
Site Manager WAN Line Services Parameters117021-A Rev. A A-49 Parameter: Extended AddressPath: COM Connector > Edit Line > Edit Sync ParametersD
Configuring WAN Line ServicesA-50 117021-A Rev. AParameter: Minimum Frame SpacingPath: COM Connector > Edit Line > Edit Sync ParametersDefault:
Site Manager WAN Line Services Parameters117021-A Rev. A A-51 Parameter: Remote AddressPath: COM Connector > Edit Line > Edit Sync ParametersDef
Configuring WAN Line ServicesA-52 117021-A Rev. AParameter: Pass Thru Remote AddressPath: COM Connector > Edit Line > Edit Sync ParametersDefaul
Site Manager WAN Line Services Parameters117021-A Rev. A A-53 Parameter: Sync Media TypePath: COM Connector > Edit Line > Edit Sync ParametersDe
Configuring WAN Line ServicesA-54 117021-A Rev. AParameter: KG84A Sync Loss IntervalPath: COM Connector > Edit Line > Edit Sync ParametersDefaul
Site Manager WAN Line Services Parameters117021-A Rev. A A-55 Parameter: KG84A Sync PulsePath: COM Connector > Edit Line > Edit Sync ParametersD
Configuring WAN Line ServicesA-56 117021-A Rev. AParameter: Sync Hold Down TimePath: COM Connector > Edit Line > Edit Sync ParametersDefault: 0
Site Manager WAN Line Services Parameters117021-A Rev. A A-57 Parameter: Sync Line CodingPath: COM Connector > Edit Line > Edit Sync ParametersD
Configuring WAN Line ServicesA-58 117021-A Rev. AParameter: Sync B Channel OverridePath: COM Connector > Edit Line > Edit Sync ParametersDefault
Site Manager WAN Line Services Parameters117021-A Rev. A A-59 Parameter: Sync PriorityPath: COM Connector > Edit Line > Edit Sync ParametersDefa
Configuring WAN Line ServicesA-60 117021-A Rev. AT1 Line ParametersYou access the T1 line parameters from the Configuration Manager.Parameter: Enable P
Site Manager WAN Line Services Parameters117021-A Rev. A A-61 Parameter: Line BuildoutPath: T1 Connector > Edit Line > Edit T1 ParametersDefault
Parameter: Mini DacsPath: T1 Connector > Edit Line > Edit T1 ParametersDefault: Idle Options: Idle | Data | Voice | Circuit 1 | Circuit 2Functio
Site Manager WAN Line Services Parameters117021-A Rev. A A-63 Multiline Configuration ParameterYou access the Data Path Chooser parameter from the Confi
Configuring WAN Line ServicesA-64 117021-A Rev. A
117021-A Rev. A B-1 Appendix BDefault Line Parameter SettingsTables B-1 to B-20 list the default settings for line attribute, multiline, and Line Reso
Configuring WAN Line ServicesB-2 117021-A Rev. AAsynchronous Line Parameters (AN and ANH only)DSU/CSU Parameters (BayStack routers only)Table B-1. Asy
Default Line Parameter Settings117021-A Rev. A B-3 E1 Line ParametersHSSI Line ParametersTable B-3. E1 Line Parameters Parameter Default Enable Enable
117021-A Rev. A xxiii About This Guide If you are responsible for configuring and managing Bay Networks ® routers, read this guide to learn about ph
Configuring WAN Line ServicesB-4 117021-A Rev. ALAPB ParametersMCE1 Line ParametersTable B-5. LAPB Parameters Parameter DefaultEnable EnableStation Ty
Default Line Parameter Settings117021-A Rev. A B-5 Table B-7. MCE1 Port Application Parameters Parameter DefaultPort Application Mode NONPRITable B-8.
Configuring WAN Line ServicesB-6 117021-A Rev. AMCT1 Line ParametersInterframe Time Fill Character FlagsCRC Size 16 bit CRCMTU Size (bytes) 1600Table
Default Line Parameter Settings117021-A Rev. A B-7 Table B-13. QMCT1 Clock Parameters Parameter DefaultPrimary Clock InternalSecondary Clock InternalT
Configuring WAN Line ServicesB-8 117021-A Rev. ATable B-15. MCT1 Logical Line Parameters Parameter DefaultEnable/Disable EnableBofL Enable/Disable Ena
Default Line Parameter Settings117021-A Rev. A B-9 Synchronous Line ParametersTable B-17. QMCT1 Logical Line Action Parameters Parameter DefaultBert M
Configuring WAN Line ServicesB-10 117021-A Rev. ALocal Address 7 (1 or 3 if X.25 is enabled) 7Remote Address 7 (1 or 3 if X.25 is enabled) 7WAN Proto
Default Line Parameter Settings117021-A Rev. A B-11 T1 Line ParametersMultiline ParametersTable B-19. T1 Line Parameters Parameter DefaultEnable Enabl
117021-A Rev. A Glossary-1 GlossaryAttributeSee parameter. Properties or functional aspects of a configurable MIB object. ChannelThe multiplexed signa
Configuring WAN Line Servicesxxiv 117021-A Rev. A Before You Begin Before using this guide, you must complete the following procedures:• For a new ro
117021-A Rev. A Index-1AaccessingDSU/CSU parameters, 4-1line service parameters, 1-2address mode, FDL HDLC, 7-13, A-30addressing, point-to-point conne
Index-2 117021-A Rev. AMCE1/MCT1, 7-5synchronous, 2-6T1, 6-6connector, defined, Glossary-1customer supportprograms, xxviitechnical response centers, xx
117021-A Rev. A Index-3Carrier Loss Debounce, A-15CRC Size, 5-5, A-15Enable, 5-2, A-12External Clock Speed, 5-4, A-14MTU, 5-3, A-13Transmission Interf
Index-4 117021-A Rev. ABERT Mode Enable, A-39BERT Test Pattern, A-39BofL Enable, A-34BofL Timeout, A-34CRC Size, A-38Enable/Disable, A-34Fractional Lo
117021-A Rev. A Index-5grouping data paths, 8-2overview, 8-1parameters, A-61supported media, 8-1synchronous lines, 8-5, 8-6traffic distribution methods
WAN Protocol, 2-12, A-50TT1configuring for multiline, 8-1default parameters, B-11DSX-1, 6-5frame format, 6-3overview, 6-1parametersB8ZS Support, 6-5, A
About This Guide 117021-A Rev. A xxv Acronyms AMI alternate mark inversion ANSI American National Standards InstituteAUI Attachment Unit Interface B
Configuring WAN Line Servicesxxvi 117021-A Rev. A LAPB Link Access Procedure BalancedLAN local area networkMAC media access controlMAU media access u
About This Guide 117021-A Rev. A xxvii Ordering Bay Networks Publications To purchase additional copies of this document or other Bay Networks publi
Configuring WAN Line Servicesxxviii 117021-A Rev. AIf you purchased a Bay Networks service program, call one of the following Bay Networks technical s
117021-A Rev. A 1-1 Chapter 1Getting StartedThis chapter describes how to access the physical and data link layer (line) services for the configured WA
117021-A Rev. A iii USA Requirements Only Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment generate
Configuring WAN Line Services1-2 117021-A Rev. AAccessing Line Parameters with Configuration ManagerThis section describes how to access the Site Manag
Getting Started117021-A Rev. A 1-3 2.Select Circuits > Edit Circuits (refer to Figure 1-1).The Circuit List window appears (Figure 1-2).Figure 1-2.
Configuring WAN Line Services1-4 117021-A Rev. A3. Select the circuit and click on Edit.The Circuit Definition window appears (Figure 1-3).Figure 1-3.
Getting Started117021-A Rev. A 1-5 Figure 1-4. Edit Lines WindowOnly multichannel and multiline circuits have more than one line listed in the Edit Li
117021-A Rev. A 2-1 Chapter 2Configuring Synchronous ServicesThis chapter describes how to edit line services for synchronous WAN circuits, including p
Configuring WAN Line Services2-2 117021-A Rev. AEditing Synchronous Line ParametersThis section describes how to edit synchronous line service paramet
Configuring Synchronous Services117021-A Rev. A 2-3 • Setting the Signaling Method• Enabling or Disabling DSR Polling• Setting the Line Coding• Specif
Configuring WAN Line Services2-4 117021-A Rev. AFigure 2-1. Edit SYNC Parameters Window (1 of 4 screens)Enabling or Disabling Synchronous ServicesThe
Configuring Synchronous Services117021-A Rev. A 2-5 We recommend that you enable BofL for point-to-point connections between Bay Networks peers. Howev
iv 117021-A Rev. A Japan/Nippon Requirements Only Voluntary Control Council for Interference (VCCI) StatementVoluntary Control Council for Interfere
Configuring WAN Line Services2-6 117021-A Rev. AEnabling or Disabling Remote Address FilteringSet the Promiscuous parameter to specify whether the int
Configuring Synchronous Services117021-A Rev. A 2-7 Setting the Internal Clock SpeedThe Internal Clock Speed parameter sets the clock speed of an inte
Configuring WAN Line Services2-8 117021-A Rev. ASet the external clock speed for the interface.Setting the Signal ModeYou use the Signal Mode paramete
Configuring Synchronous Services117021-A Rev. A 2-9 Figure 2-2 shows the next ten synchronous parameters.Figure 2-2. Edit SYNC Parameters Window (2 of
Configuring WAN Line Services2-10 117021-A Rev. ASpecifying the Link Level ProtocolThe Service parameter specifies the link-level protocol for this int
Configuring Synchronous Services117021-A Rev. A 2-11 Specifying Point-to-Point AddressesAccording to convention, one end of a point-to-point circuit i
Configuring WAN Line Services2-12 117021-A Rev. AConventional addressing designates routers A, B, and C as DCE (address = 01) and routers X, Y, and Z
Configuring Synchronous Services117021-A Rev. A 2-13 Setting Pass-Through AddressesYou can assign a local MAC address to the local interface using the
Configuring WAN Line Services2-14 117021-A Rev. AFigure 2-4 shows the next ten synchronous parameters.Figure 2-4. Edit SYNC Parameters Window (3 of 4
Configuring Synchronous Services117021-A Rev. A 2-15 Set the media type used for the interface.Enabling or Disabling DSR PollingBy default, a synchron
117021-A Rev. A v Canada Requirements Only Canada CS-03 Rules and Regulations Note: The Canadian Department of Communications label identifies cert
Configuring WAN Line Services2-16 117021-A Rev. AConfiguring KG84A SecurityKG84A is a cryptographic device used to secure data transmitted over a point
Configuring Synchronous Services117021-A Rev. A 2-17 • KG84A Cycle• KG84A Synchronization Loss Interval• KG84A Remote Resync Wait• KG84A Synchronizati
Configuring WAN Line Services2-18 117021-A Rev. AUse different settings at each end of the point-to-point link to avoid a possible race condition.Confi
Configuring Synchronous Services117021-A Rev. A 2-19 Figure 2-6 shows the next ten synchronous parameters.Figure 2-6. Edit SYNC Parameters Window (4 o
Configuring WAN Line Services2-20 117021-A Rev. ASet the length of the Link Idle Timer parameter to a value from 1 to 9999 seconds.Enabling or Disabli
Configuring Synchronous Services117021-A Rev. A 2-21 By default, the Cable Type parameter is set to Null. Set the cable type for the interface.Setting
Configuring WAN Line Services2-22 117021-A Rev. AEnable or disable remote loopback detection for the interface.Setting the Hold Down TimeOn a synchron
Configuring Synchronous Services117021-A Rev. A 2-23 Figure 2-7. Edit SYNC Parameters Window (4 of 4, Octal Sync only)Setting the B Channel OverrideOn
Configuring WAN Line Services2-24 117021-A Rev. AIf your ISDN service provider offers only 2B + D service, the FLOATINGB option enables you to use onl
Configuring Synchronous Services117021-A Rev. A 2-25 For all other synchronous link modules, these parameters are not available. Refer to Chapter 3 fo
vi 117021-A Rev. A Canada Requirements Only (continued) D. O. C. Explanatory Notes: Equipment Attachment Limitations The Canadian Department of Com
Configuring WAN Line Services2-26 117021-A Rev. ALAPB Implementation on Bay Networks RoutersThe implementation of the LAPB protocol differs among Bay
Configuring Synchronous Services117021-A Rev. A 2-27 • Setting the T3 Disconnect Timer• Selecting the Local Command or Response Address• Viewing the W
Configuring WAN Line Services2-28 117021-A Rev. AEnabling or Disabling LAPB ServicesThe router enables LAPB line services when you configure a synchron
Configuring Synchronous Services117021-A Rev. A 2-29 Setting the Maximum N1 Frame SizeThe Max N1 Frame Size parameter specifies the frame size, in byte
Configuring WAN Line Services2-30 117021-A Rev. ASetting the T1 Acknowledge TimerThe Max T1 Acknowledge Timer specifies the maximum time, in seconds, t
Configuring Synchronous Services117021-A Rev. A 2-31 Setting the Link Setup ActionThe Link Setup Action parameter identifies whether or not the router
Configuring WAN Line Services2-32 117021-A Rev. ASelecting the Local Command or Response AddressThe Command/Response Address parameter specifies the lo
117021-A Rev. A 3-1 Chapter 3Configuring BayStack AN and ANHAsynchronous ServicesThis chapter describes how to edit asynchronous services for BayStack
Configuring WAN Line Services3-2 117021-A Rev. AFigure 3-1. Edit Async Parameters WindowEnabling or Disabling the Asynchronous DriverThe router enable
Configuring BayStack AN and ANH Asynchronous Services117021-A Rev. A 3-3 Setting the MTUThe largest packet size that this interface can transmit via T
117021-A Rev. A vii Canada Requirements Only (continued) Canadian Department of Communications Radio Interference Regulations This digital apparat
Configuring WAN Line Services3-4 117021-A Rev. ASetting the Maximum Transmit Queue LengthThe Cfg TxQ Length parameter specifies the maximum length of t
Configuring BayStack AN and ANH Asynchronous Services117021-A Rev. A 3-5 With the Start Protocol set to Originate, you must also configure the• Remote
Configuring WAN Line Services3-6 117021-A Rev. ASetting the TCP Receive Window SizeBy default, the router sets the TCP receive window for received asy
Configuring BayStack AN and ANH Asynchronous Services117021-A Rev. A 3-7 If the interface is listening for an incoming connection, you can specify a n
117021-A Rev. A 4-1 Chapter 4Configuring BayStack DSU/CSU ServicesThis chapter describes how to edit parameters for an internal DSU/CSU installed in Ba
Configuring WAN Line Services4-2 117021-A Rev. A2. Click on Edit DSU/CSU.The Edit Adapter Module DSU CSU Parameters window appears (Figure 4-2).Figure
Configuring BayStack DSU/CSU Services117021-A Rev. A 4-3 Setting the Option ModeThe DSU/CSU module supports communication to either 56-Kb/s Digital Da
Configuring WAN Line Services4-4 117021-A Rev. AThe 64K Transmit Monitor is disabled by default. Keep the parameter Disabled to allow all data; set to
Configuring BayStack DSU/CSU Services117021-A Rev. A 4-5 Figure 4-4. Edit Adapter Module DSU CSU Parameters Window3.Edit the V.54 Loopback and V.54 Ti
viii 117021-A Rev. A T1 Service Compliance Statements T1 Service NOTE: This T1 Service notice applies to you only if you have received a single or d
Configuring WAN Line Services4-6 117021-A Rev. ASelect a test state or keep the default, No Loopback. Refer to “Loopback Test Modes,” later in this ch
Configuring BayStack DSU/CSU Services117021-A Rev. A 4-7 Loopback Test ModesYou can activate DSU/CSU tests from the Configuration Manager, as described
Configuring WAN Line Services4-8 117021-A Rev. ARemote Digital Loopback (RL)Remote Digital Loopback (CCITT V.54 Loopback) tests the local router DSU/C
Configuring BayStack DSU/CSU Services117021-A Rev. A 4-9 Pattern-2047 BERT Test In the Pattern-2047 test, the DSU sends a 2047 BERT pattern to the car
117021-A Rev. A 5-1 Chapter 5Configuring HSSI ServicesThis chapter describes how to edit the line services for HSSI link modules, in the following sect
Configuring WAN Line Services5-2 117021-A Rev. AFigure 5-1. Edit HSSI Parameters WindowEnabling or Disabling HSSI LinesBy default, the router enables
Configuring HSSI Services117021-A Rev. A 5-3 With BofL enabled, the router sends periodic keep-alive messages to the remote peer. If you enable BofL l
Configuring WAN Line Services5-4 117021-A Rev. AViewing the Configured WAN ProtocolYou can view which WAN protocol is enabled on a HSSI circuit. Howeve
Configuring HSSI Services117021-A Rev. A 5-5 You can set the external clock speed to a rate from 307200 to 52638515 bytes/s.Select a value equal or cl
117021-A Rev. A ix Bay Networks Software License This Software License shall govern the licensing of all software provided to licensee by Bay Netwo
117021-A Rev. A 6-1 Chapter 6Configuring E1 or T1 ServicesThis chapter describes customizing line parameters for E1 or T1 WAN interfaces in the followi
Configuring WAN Line Services6-2 117021-A Rev. ARefer to Chapter 1 for information about accessing the T1 Line Entry window (Figure 6-1).Figure 6-1. T
Configuring E1 or T1 Services117021-A Rev. A 6-3 Setting the T1 Frame TypeT1 framing digitizes analog signals into a level-zero digital signal (DS0) w
Configuring WAN Line Services6-4 117021-A Rev. AEnabling or Disabling Bipolar with 8-Zero SubstitutionT1 uses bipolar format for signals. In bipolar f
Configuring E1 or T1 Services117021-A Rev. A 6-5 Figure 6-3. Bipolar with 8-Zero SubstitutionYou can enable or disable B8ZS support on this interface,
Configuring WAN Line Services6-6 117021-A Rev. ASetting the Internal Clock ModeThe T1 equipment associated with a T1 interface must use a compatible t
Configuring E1 or T1 Services117021-A Rev. A 6-7 Data and Voice Pass-ThroughTo enable data and voice pass-through, assign identical channels to data o
Configuring WAN Line Services6-8 117021-A Rev. AFigure 6-4. E1 Line Entry WindowRefer to Chapter 2 for information about editing synchronous line para
Configuring E1 or T1 Services117021-A Rev. A 6-9 Enabling or Disabling CRC CheckingSome E1 equipment expects a 4-byte CRC trailer at the end of each f
Mais documentos para Redes Avaya Configuring WAN Line Services
Manuais e produtos relacionados com Redes Avaya Configuring WAN Line Services
(147 páginas)
(26 páginas)
(54 páginas)
(92 páginas)
(26 páginas)
(42 páginas)
(23 páginas)
(52 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.102 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais