Avaya Configuring ATM Services Manual do Utilizador Página 140
- Página / 268
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuring ATM Services
11-4 114056 Rev. A
Setting the SCR
For ATM FRE2 ILI pairs, the SCR is the upper bound on the conforming average
rate of an individual PVC or control VC. In this definition, average rate is the
number of cells transmitted over the link divided by the duration of the
connection. The duration of the connection equals the total amount of time it takes
from connection setup to connection release.
The SCR allows you to define future cell flow on a PVC or control VC in greater
detail than by just using the PCR. For ATM FRE2 ILI pairs, the SCR controls the
rate over time -- not at a specific instant of time -- and can help you more
efficiently use your network resources. In other words, the SCR allows sufficient
bandwidth for operation, but does not allow a bandwidth as high as the PCR.
For ATM ARE ILI pairs and Model 5780 ATM routers, the SCR value maps
directly to a MCR value. In other words, when you configure the SCR on one of
these devices, you actually configure the MCR. Instead of defining the upper
bound of an average rate, like the SCR, the MCR defines the minimum amount of
guaranteed bandwidth allowed for PVCs and Control VCs on the ATM line.
The MCR (that is, SCR) not only controls the rate over time, it guarantees this
rate. In other words, the SCR provides sufficient bandwidth for SVC operation
but, at the same time, guarantees the bandwidth for PVCs and control VCs on the
ATM line.
When setting the SCR for ATM FRE2 ILI pairs, keep the following in mind:
• The SCR is essentially a future average. By setting the SCR you are
specifying the cell rate, over time, to which you want the VC to conform.
• To be useful, the SCR must not exceed the PCR.
• If you know the user average rate, set the SCR about 10 percent higher than
this value.
• ATM FRE2 ILI pairs require a minimum SCR value of 300 cells/s. PVCs may
fail to operate with SCR values less than 300 cells/s.
When setting the SCR for ATM ARE ILI pairs and Model 5780 ATM routers, keep
the following in mind:
• The SCR maps directly to the MCR.
• The MCR provides guaranteed bandwidth for PVCs and control VCs while
allowing sufficient bandwidth for SVCs to operate.
- Configuring ATM 1
- Services 1
- Bay Networks Software License 3
- (continued) 4
- Contents 5
- 114056 Rev. A 10
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- World Wide Web 27
- Customer Service FTP 27
- Support Source CD 28
- CompuServe 28
- InfoFACTS 29
- How to Get Help 29
- Chapter 1 31
- Starting ATM 31
- Adding ATM to the Router 32
- Defining a Service Record 33
- 114056 Rev. A 1-5 35
- Supported Protocols 36
- Adding PVCs 38
- Chapter 2 41
- Understanding ATM Concepts 41
- 2-2 114056 Rev. A 42
- Figure 2-2. ATM Cell Header 42
- Data Transmission 43
- VP = Virtual path 44
- VC = Virtual channel 44
- Physical Layer 45
- ATM Layer 46
- ATM Adaptation Layer (AAL5) 47
- 2-8 114056 Rev. A 48
- Data Encapsulation 49
- 2-10 114056 Rev. A 50
- Encapsulation Rules for PVCs 52
- PVC Access Methods 53
- 2-14 114056 Rev. A 54
- Hybrid Access 55
- 2-16 114056 Rev. A 56
- Figure 2-8. Hybrid PVCs 56
- SVC Access Methods 58
- ATM Traffic Parameters 58
- Variable Bit Rate 59
- Available Bit Rate 59
- Rules for Editing Protocols 60
- ARP and Inverse ARP Support 60
- ATM Error Checking 61
- Converting Mb/s to Cells/s 61
- Example of an ATM Network 62
- Hardware Devices 64
- 2-26 114056 Rev. A 66
- For More Information 68
- Chapter 3 71
- 3-2 114056 Rev. A 72
- ATM Address Resolution 73
- 3-4 114056 Rev. A 74
- 114056 Rev. A 3-5 75
- Chapter 4 77
- LAN Emulation Components 78
- LAN Emulation Server 79
- Broadcast and Unknown Server 79
- 4-4 114056 Rev. A 80
- Initial State 81
- LECS Connect State 81
- Configure State 81
- Join State 81
- Initial Registration State 82
- BUS Connect State 82
- Operational State 82
- Chapter 5 85
- Customizing an ATM Line 85
- 5-2 114056 Rev. A 86
- Assigning the Framing Mode 87
- Defining ATM Cell Insertion 88
- Defining the Interface MTU 89
- 5-6 114056 Rev. A 90
- Specifying DS3 Line Build Out 92
- Chapter 6 95
- Service Records 95
- Autogenerating ATM Addresses 96
- Assigning ATM Addresses 97
- 6-4 114056 Rev. A 98
- Entering an Emulated LAN Name 100
- Defining an Emulated LAN Type 100
- Defining the MTU 101
- Where to Go Next 102
- Chapter 7 103
- Customizing PVCs 103
- Setting a VCI Number 104
- Setting the PCR 105
- Configuring ATM Services 106
- 7-4 114056 Rev. A 106
- Table 7-1. Valid PCR Ranges 106
- Setting the SCR 107
- 7-6 114056 Rev. A 108
- Table 7-2. Valid SCR Ranges 108
- Setting the MBS 109
- Setting the Transmit SDU Size 110
- Setting the Receive SDU Size 110
- Chapter 8 113
- Specifying an Owner 114
- Entering an ELAN Name 114
- Entering a LES ATM Address 114
- Selecting a Configuration Mode 115
- 8-4 114056 Rev. A 116
- Setting the Control Timeout 117
- Setting the Aging Time 118
- 114056 Rev. A 8-7 119
- Setting the Flush Timeout 120
- Entering a LECS ATM Address 121
- Chapter 9 123
- Customizing Signaling 123
- Assigning a Protocol Standard 124
- Setting Connection Thresholds 125
- Setting Signaling Timers 126
- 9-6 114056 Rev. A 128
- 9-8 114056 Rev. A 130
- Defining Retransmissions 131
- Pacing Calls 131
- Chapter 10 133
- Customizing ILMI 133
- Setting the ILMI Get Timer 134
- Setting the ILMI Set Timer 135
- Chapter 11 137
- Changing the ILMI VPI Number 138
- Changing the ILMI VCI Number 138
- Table 11-1. Valid PCR Ranges 139
- Table 11-2. Valid SCR Ranges 141
- Chapter 12 145
- Customizing SAAL 145
- Enabling or Disabling SAAL 146
- Modifying SAAL Timers 146
- Defining PDU Values 148
- Appendix A 151
- Site Manager Parameters 151
- A-2 114056 Rev. A 152
- Using the Menu Path 153
- A-4 114056 Rev. A 154
- 155
- 158
- 162
- A-14 114056 Rev. A 164
- A-18 114056 Rev. A 168
- 170
- A-22 114056 Rev. A 172
- 174
- A-26 114056 Rev. A 176
- A-28 114056 Rev. A 178
- A-30 114056 Rev. A 180
- 181
- 182
- A-34 114056 Rev. A 184
- A-38 114056 Rev. A 188
- A-40 114056 Rev. A 190
- 191
- A-42 114056 Rev. A 192
- A-44 114056 Rev. A 194
- A-46 114056 Rev. A 196
- A-48 114056 Rev. A 198
- A-50 114056 Rev. A 200
- ILMI category 202
- A-54 114056 Rev. A 204
- A-56 114056 Rev. A 206
- A-58 114056 Rev. A 208
- A-60 114056 Rev. A 210
- 212
- A-64 114056 Rev. A 214
- 216
- A-68 114056 Rev. A 218
- A-70 114056 Rev. A 220
- Appendix B 221
- B-2 114056 Rev. A 222
- ATM FRE2 Line Parameters 224
- ATM ARE Line Parameters 224
- (continued) 225
- B-6 114056 Rev. A 226
- Appendix C 229
- ATM Sample Log 229
- C-2 114056 Rev. A 230
- C-4 114056 Rev. A 232
- C-6 114056 Rev. A 234
- C-8 114056 Rev. A 236
- C-10 114056 Rev. A 238
- C-12 114056 Rev. A 240
- C-14 114056 Rev. A 242
- C-16 114056 Rev. A 244
- C-18 114056 Rev. A 246
- C-20 114056 Rev. A 248
- C-22 114056 Rev. A 250
- C-24 114056 Rev. A 252
- C-26 114056 Rev. A 254
- 114056 Rev. A Index-1 257
- 114056 Rev. A Index-3 259
- 114056 Rev. A Index-5 261
- 114056 Rev. A Index-7 263
- 114056 Rev. A Index-9 265
- 114056 Rev. A Index-11 267
Manuais e produtos relacionados com Redes Avaya Configuring ATM Services
Redes Avaya R1.3 Guia de Configuração
(13 páginas)
(13 páginas)
Redes Avaya T1/E1 Manual do Utilizador
(24 páginas)
(24 páginas)
Redes Avaya BayRS, BCC, and Site Manager Software Version 15.0.0.0 Fixed Anomalies Manual do Utilizador
(30 páginas)
(30 páginas)
Redes Avaya X.25 Manual do Utilizador
(272 páginas)
(272 páginas)
Redes Avaya Attendant Console Manual do Utilizador
(62 páginas)
(62 páginas)
Redes Avaya BCM200/400 Manual de Instalação
(374 páginas)
(374 páginas)
Redes Avaya BCM First Time Guia de Instalação
(14 páginas)
(14 páginas)
Redes Avaya IPv6 Manual do Utilizador
(162 páginas)
(162 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais