Avaya Configuring IP, ARP, RIP, and OSPF Services Manual do Utilizador Página 212
- Página / 374
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuring IP, ARP, RARP, RIP, and OSPF Services
6-34
308627-14.00 Rev 00
Specifying the MTU Size
OSPF recognizes a maximum transmission unit (MTU) size for updates
transmitted on an interface. By default, when you configure OSPF on an interface,
OSPF uses the MTU size specified for the type of network to which the interface
is connected.
Using the BCC or Site Manager, you can configure OSPF to do the following:
• Send packets no larger than the IP MTU size for Ethernet (1500).
• Use the MTU size that you specify. The number you enter must be less than
the IP MTU size for that physical interface.
Using the BCC
To specify the MTU size, navigate to an OSPF interface prompt (for example,
box; eth 2/2; ip/2.2.2.2/255.255.0.0; ospf
) and enter:
mtu
<
size>
size
is 1, 2, or the MTU size in bytes.
For example, the following command sets the MTU to 2 on IP interface 2.2.2.2. A
value of 2 sends packets no larger than the IP MTU size for Ethernet (1500).
ospf/2.2.2.2#
mtu 2
ospf/2.2.2.2#
Note:
When running OSPF over a synchronous/PPP link, set the MTU size to
a value less than the synchronous MTU size (1200). This setting allows all
OSPF routes to be learned over the link.
- Configuring IP, ARP, RARP 1
- RIP, and OSPF Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308627-14.00 Rev 00 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Related Publications 21
- How to Get Help 22
- Chapter 1 23
- IP Addresses 24
- Subnet Addressing 26
- Supernet Addressing 29
- Autonomous Systems 30
- Figure 1-4. ARP Example 32
- OSPF Neighbors 36
- Neighbor Adjacencies 36
- Designated Routers 37
- OSPF Areas 38
- OSPF Router Types 40
- AS External Routes 40
- OSPF Implementation Notes 41
- Router Discovery Protocol 42
- Route Preferences 42
- Route Weights 43
- Figure 1-7. IP Routing Table 45
- IP Traffic Filters 48
- Chapter 2 49
- Starting IP Services 49
- Starting RIP 51
- Starting OSPF 52
- Starting Router Discovery 52
- Adding RIP to an IP Interface 55
- Starting RARP 57
- Chapter 3 63
- Caution: 80
- Customizing an IP Interface 82
- IP0012A 97
- Configuring an SMDS Address 100
- (continued) 101
- Using the BCC 103
- Using Site Manager 104
- Deleting IP from an Interface 107
- Defining a Static Route 111
- 3.2.4.5/255.255.0.0: 113
- Choosing a Broadcast Type 118
- Chapter 4 123
- Customizing ARP 124
- Customizing Global ARP 125
- (continued) 129
- Figure 4-1. Proxy ARP Example 130
- Customizing RARP 134
- Deleting RARP Globally 137
- Chapter 5 139
- Customizing RIP Services 139
- Setting the RIP Diameter 140
- Customizing a RIP Interface 141
- Selecting the RIP Version 142
- Specifying the Update Mode 147
- Sending Triggered Updates 149
- Listening for a Default Route 155
- Defining a RIP Accept Policy 163
- Chapter 6 179
- Customizing OSPF Services 179
- Supplying an OSPF Router ID 182
- Figure 6-1. OSPF ASE Routes 187
- Setting the Holddown Timer 192
- Configuring Message Logging 193
- Configuring an Area ID 198
- Specifying the Interface Type 199
- Estimating the Transit Delay 202
- Setting the Hello Interval 205
- Setting the Dead Interval 207
- Specifying the Metric Cost 209
- Table 6-6. Cost Settings 210
- Specifying the MTU Size 212
- Defining an Area 218
- Configuring Authentication 221
- Configuring a Summary Route 222
- Configuring a Stub Area 224
- 0.0.0.1: 229
- Policies 247
- Appendix A 251
- Site Manager Parameters 251
- IP Parameters 252
- IP Interface Parameters 254
- IP Global Parameters 269
- Static Route Parameters 276
- Adjacent Host Parameters 280
- Router Discovery Parameters 283
- RARP Parameters 285
- OSPF Parameters 287
- OSPF Interface Parameters 292
- OSPF Area Parameters 301
- Area Range Parameters 305
- OSPF NSSA Range Parameters 308
- RIP Parameters 314
- Appendix B 321
- Routing Policy Parameters 321
- RIP Accept Policy Parameters 325
- OSPF Accept Policy Parameters 326
- Appendix C 343
- RIP Export Filters 347
- OSPF Import Filters 350
- OSPF Export Filters 351
- Appendix D 355
- Route Weight Worksheet 355
- Appendix E 359
- IP/OSPF Configuration Example 359
- 10.1.1.0 360
- 255.255.255.0 (RIP Only) 360
Manuais e produtos relacionados com Redes Avaya Configuring IP, ARP, RIP, and OSPF Services
Redes Avaya BCM450 Manual do Utilizador
(22 páginas)
(22 páginas)
Redes Avaya BSGX4e Guia do Utilizador
(206 páginas)
(206 páginas)
Redes Avaya a WAN Adapter Module in a BayStack ARN Router (114204 Rev. A) Manual do Utilizador
(34 páginas)
(34 páginas)
Redes Avaya Integrated Management Release 2.2 Network Management Console Guia do Utilizador
(154 páginas)
(154 páginas)
Redes Avaya VLANs BCM Rls 6.0 Manual do Utilizador
(22 páginas)
(22 páginas)
Redes Avaya 1100-Series Manual do Utilizador
(48 páginas)
(48 páginas)
Redes Avaya BCM50 2.0 Guia do Utilizador
(26 páginas)
(26 páginas)
Redes Avaya 0604DAX Aviso
(20 páginas)
(20 páginas)
Redes Avaya 2050 IP Softphone Manual do Utilizador
(26 páginas)
(26 páginas)
Redes Avaya R5.0: Guia de Configuração
(20 páginas)
(20 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais